Page 1
The RFID System Can Be Used Just Like a Sensor. V680-HAM91/HAM81 Read or write 16 bits at a time with one unit. Useful in applications from simple line sorting or product identification to managing work progress or inspection data.
Note 1. Attach an Antenna to the V680-HAM42-DRT DeviceNet ID Slave to read and write V680 ID Tag data. 2. The DeviceNet ID Slave can communicate with ID Tags that comply with ISO/IEC 18000-3 (ISO/IEC 15693) in addition to V680-series ID Tags.
Page 3
Note 1. Attach an Antenna to the V680-HAM91/-HAM81 ID Flag Sensor to read and write V680 ID Tag data. 2. The DeviceNet ID Slave can communicate with ID Tags that comply with ISO/IEC 18000-3 (ISO/IEC 15693) in addition to V680-series ID Tags.
2. The cables can be extended to a maximum length of 10 m. Amplifier: ID Flag Sensor 3. Normally two Interface Cables are required for 1 Unit. If you do not need to write to ID Tags, or use the address shift or noise check...
Metallic compatibility Note 1. Refer to the User's Manual (Cat. No. Z278 or Z279) for data backup time for temperatures of 85°C or higher. If the V680 has been stored at 125°C or higher, write the data again even if the data does not need to be changed.
Page 6
Note 1. The degree of protection for the Connector is IP67/IP65. This OMRON in-house standard confirms resistance to cutting and other oils. It is equivalent to the former JEM standard. 2. The Connector is not waterproof. This OMRON in-house standard confirms resistance to cutting and other oils. It is equivalent to the former JEM standard.
Page 7
DIN Track Note 1. For details, refer to the User's Manual (Cat. No. Z278). 2. The number of words allocated in the master depends on the Access Mode. Refer to page 9 for information on Part Names and Operating Modes.
Page 8
Note 1. For details, refer to the User's Manual (Cat. No. Z278). 2. The connectors are not water resistant. If there is a possibility that water will be splashed onto the ID Sensor Unit, mount it inside of a control box. Also, be sure to use the V680 as a set with the V680-A60 Interface Cable (sold separately).
Antenna.) Setting prohibited Note 1. The V600-compatible Trigger and Auto Modes can be used with the same I/O settings and control methods that are used with the V600- HAM42-DRT. 2. Communications with the host device will be offline while the Communications Test Mode or Noise Measurement Mode is being used.
Address Shift When reading or writing more than 16 bits (2 bytes), an address shift can be specified to enable reading or writing up to 128 bits (16 addresses). The address shift can be set from the host, eliminating the need to change the address set on the front panel.
Page 11
Note 1. When mounting the V680-HS65, be sure to attach the Mounting Brackets at the base of the Antenna. The enclosed Mounting Brackets do not need to be used, however, if the mounting brackets on the Antenna are metal plates and their dimensions are larger than the dimensions of the Antenna (100 ×...
Page 12
Recommended combination Function Transmission distance ID Tag and Read/Write Antenna mounting (unit: mm) conditions ID Tag Read/Write Antenna V680-D1KP66T V680-HS52 Read 1.0 to 17.0 mm V680-D1KP66T (axial deviation ±2) distance (See note 2.) V680-HS52 Write 1.0 to 17.0 mm (axial deviation ±2) distance (See note 2.)
Page 13
Note 1. When mounting the V680-HS65, be sure to attach the Mounting Brackets at the base of the Antenna. The enclosed Mounting Brackets do not need to be used, however, if the mounting brackets on the Antenna are metal plates and their dimensions are larger than the dimensions of the Antenna (100 ×...
Page 14
ID Tag (2-kbyte Memory) Transmission Recommended combination Function Transmission distance ID Tag and Read/Write Antenna mounting (unit: mm) conditions ID Tag Read/Write Antenna V680-D2KF52M V680-HS51 Read 0.5 to 5.5 mm V680-D2KF52M (axial deviation ±2) distance Non-metallic (Resin, plastic, wood, etc.)
Page 15
Note: When mounting the V680-HS65, be sure to attach the Mounting Brackets at the base of the Antenna. The enclosed Mounting Brackets do not need to be used, however, if the mounting brackets on the Antenna are metal plates and their dimensions are larger than the dimensions of the Antenna (100 ×...
1-kbyte Memory ID Tag The values given for communications ranges are reference values. Refer to pages 11 to 13 for communications distance specifications. The communications distance will depend on the ID Tags, ambient temperature, surrounding metal, noise, and other factors. Test operation completely when installing a system.
Page 18
2-kbyte Memory ID Tag The values given for communications ranges are reference values. Refer to pages 14 to 15 for communications distance specifications. The communications distance will depend on the ID Tags, ambient temperature, surrounding metal, noise, and other factors. Test operation completely when installing a system.
Page 20
8-/32-Kbyte Memory ID Tag The values given for communications ranges are reference values. Refer to pages 15 for communications distance specifications. The communications distance will depend on the ID Tags, ambient temperature, surrounding metal, noise, and other factors. Test operation completely when installing a system.
Page 21
Processing Times (for reference purposes only) Communications times between the Antenna and ID Tag, plus the processing time for the Amplifier. V680-HAM42-DRT (DeviceNet ID Slave) 1-Kb Memory Tag V680-D1KP@ (V680-HS@@ Antenna) Communications Command Communications time (ms) speed setting 4-byte Access Mode 26-byte Access Mode 58-byte Access Mode...
69 (m/min) 43 (ms) Note 1. The travel speed depends on communications distance Y and axis offset. It is recommended to refer to the communications area diagram and use the part with the widest area. 2. These values are guidelines. Perform testing with the actual device before operation.
ID Tags. If any of these devices are nearby, communications with ID Tags may be affected or ID Tags may be destroyed. If the product is to be used near such devices, check the effects on communications before using the Note: This catalog is intended only to help select the appropriate product.
Page 24
Dimensions Note: All units are in millimeters unless otherwise indicated. ID Tag V680-D1KP52MT/-D2KF52M V680-D1KP66T/-D1KP66MT Mounting Hole Dimensions R0.2 Four, R4 ±0.2 Four, R3 dia. Two, M3 −0.1 Two, ±0.2 ±0.2 3.5 dia. −0.1 ±0.2 Two, ±0.1 Case material PPS resin 6 dia.
Page 25
14.5 dia. 16.5 dia. 16.5 dia. 5.5-dia. coaxial cable Connector Ferrite core Operation indicator Mounting Hole Dimensions Case material ABS resin Two, M4 or 4.5 dia. Filling Epoxy resin Center of coil Cable V680-HS63-R Insulated cover ±0.1 14.5 dia. 16.5 dia.
Page 26
14.4 ±5 ±5 ±5 ±5 ±5 9-dia. (0.2-dia per 7 conductors) vinyl-insulated round cable with 23 conductors Note: The connectors are not water resistant. Model Length L1 (mm) V680-A60 2M 2,000 mm V680-A60 5M 5,000 mm V680-A60 10M 10,000 mm...
Page 28
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: •...