Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TYROLIT Hydrostress FSE808
Summary of Contents for TYROLIT Hydrostress FSE808
- Page 1 FSE808 Index 000 Originalbetriebsanleitung 11007309 en / 18.08.2023...
- Page 2 Congratulations! TYROLIT TYROLIT TYROLIT TYROLIT Hydrostress Copyright © TYROLIT Hydrostress TYROLIT Hydrostress AG Witzbergstrasse 18 CH-8330 Pfäffikon Switzerland Telefon 0041 (0) 44 952 18 18 Telefax 0041 (0) 44 952 18 00...
-
Page 3: Table Of Contents
FSE808 Table of contents Safety ........................... 5 General safety notes .................... 5 1.1.1 Warning notices and symbols in this manual ..........5 1.1.2 Warning and safety notices: ................6 1.1.3 Operating manual .................... 8 Properties & advantages ....................9 General safety informatioen ..................10 Intended use policy .................... - Page 4 FSE808 Check rotational direction .................. 33 Lower/raise the saw blade and set the depth ............ 34 Relocating the floor saw ..................35 Cutting with the saw blade guard open ............. 36 Cutting special forms ..................37 Switch off the floor saw ..................37 Servicing ........................
-
Page 5: Safety
FSE808 1 Safety 1.1 General safety notes 1.1.1 Warning notices and symbols in this manual Signal word Type and source of the hazard Consequence of non-compliance. ► Action to avert the danger. The signal word after the hazard symbol indicates the level of danger: This signal word indicates an extremely dangerous situation. -
Page 6: Warning And Safety Notices
FSE808 1.1.2 Warning and safety notices: Read the operating manual Wear hearing protection Wear safety goggles Wear gloves Wear a protective helmet Wear suitable work clothes and wash dusty clothes Remove the power plug before working on the machine Risk of cuts on rotating tool Wait for all parts to stop moving. - Page 7 FSE808 Disconnect from mains before performing maintenance work Parking brake Clutch for traction drive Running direction of saw blade Instructions for avoiding damages Only store and transport the unit in an upright position Sound power level of the machine Visual inspection...
-
Page 8: Operating Manual
FSE808 1.1.3 Operating manual Preface This operating manual makes it easier to become acquainted with the machine and make full use of it as intended. The operating manual contains important information on how to operate the machine safely, properly and economically. Following it will help to prevent hazards, avoid repair costs and downtimes, and increase the reliability and service life of the machine. -
Page 9: Properties & Advantages
FSE808 2 Properties & advantages Thanks to the optimum weight distribution of the FSE808 the 7.5 kW/400 V electrical engine provides for excellent cutting power.. Due to the compact, easy-to-handle design, every corner of the construction site can be reached ... -
Page 10: General Safety Informatioen
FSE808 3 General safety informatioen 3.1 Intended use policy The manufacturer and supplier assume no liability for inappropriate use or usage other than the intended use. No alterations may be made to the machine unless carried out by the manufacturer. Changes resulting from extensions or conversions to the floor saw may only be executed with written permission of the manufacturer. -
Page 11: Organizational Measures
FSE808 Organizational measures This operating manual must be kept within easy reach for everybody at the place of use. It is to be kept for future reference or resale of the machine. Supplements to the operating manual include general statutory and other binding regulations for preventing accidents and protecting the environment and must be obeyed. -
Page 12: Choice Of Personnel And Qualifications; Fundamental Obligations
FSE808 3.3 Choice of personnel and qualifications; fundamental obligations Operators must be at least 18 years of age and mentally and physically capable of operating the floor saw. All persons must be instructed in the operation and be expressly assigned, in writing by the employer, to operate the floor saw. -
Page 13: Commissioning
FSE808 3.4.2 Commissioning Protect hands from sharp edges when fitting the saw blade. Ensure that the ground/floor has adequate load-bearing capacity. All obstacles must be removed from the cutting area and good lighting must be provided. Visually check the floor saw for damage and defects. Check the safety set-up in particular. -
Page 14: Relocating The Floor Saw
FSE808 3.4.4 Relocating the floor saw The floor saw may only be relocated when the saw blade is stopped. Before leaving the floor saw’s operating position, the motor must be turned off and the saw blade must stop. A rotating saw blade poses a high risk of injury. -
Page 15: Elektrische Energie
FSE808 3.5.2 Elektrische Energie Only use original fuses with the specified amperage. The floor saw must be immediately shut off in the event of malfunctions. Electrical work may only be carried out by certified qualified experts. The machine’s electrical equipment must be inspected and tested at regular intervals. -
Page 16: Packaging And Storage
FSE808 3.7 Packaging and storage In order to ensure sufficient protection during dispatch and transport, the machine and its components have been carefully packed. On receipt of the machine, it should be checked for damage. The device packaging consists of recyclable materials. Please place these into the appropriate collection containers, so that they can go for recycling. -
Page 17: Device Description
FSE808 4 Device description 4.1 Machine part names Pos. 1 Rear tracking pointer Pos. 11 Hinged guard Pos. 2 GEKA water connection Pos. 12 Guard flange cover Pos. 3 Cutting depth adjustment crank Pos. 13 Spray guard Pos. 4 Cutting depth adjustment lock Pos. -
Page 18: Technical Data
FSE808 4.2 Technical data TYROLIT FSE808 max. Schnitttiefe 320 mm 320 mm / 13” max. cutting depth 800 mm / 31.5” max. saw blade diameter 25.4 mm / 10” Saw blade arbor Saw blade rpm 1400 1/min (RPM) Left/right-hand cut... -
Page 19: Sound Power Level
The specified value was determined using the maximum saw blade diameter. The effects can be inversely proportional to the weight of the operator. Vibration total value: FSE808 / unter 2,5 m/s The following standards were observed during measurement: EN ISO 5349, VD 2057 Blatt 2, Richtlinie 2002/42/EG. -
Page 20: Electrical Voltage
FSE808 4.5 Electrical voltage WARNING Electric Shock Hazard The machine works with high voltages and currents. The user may suffer fatal electric shocks due to damaged cables or defective electrical components. ► Replace defective cables or components immediately ► Do not use if the machine cannot be switched on or off via the switch ►... - Page 21 FSE808 Power source When connecting to site power distribution systems, care must be taken to ensure that the individual phases evenly. The socket must be fused with a universal current-sensitive RCD type B. If power generators are used, they must deliver three times the power of the device to be operated.
-
Page 22: Transport
FSE808 5 Transport 5.1 Transport position WARNUNG Risk of being crushed by an unsecured machine Injuries due to the machine unintentionally changing position or falling parts ► Only transport the floor saw in the transport position ► Secure the machine via suitable attachment points. -
Page 23: Disassemble Into Individual Parts For Transport
FSE808 5.2 Disassemble into individual parts for transport WARNING Crush hazard or electric shock hazard Improper assembly or damage during transport can result in personal injuries or property damage ► Always perform assembly, disassembly and transport carefully. ► Check the machine for transport damage before assembly Proceed as follows ►... -
Page 24: Commissioning
FSE808 Commissioning 6.1 Consumables Lubricant The grease used on the floor saw is called "Energrease LS2 BP". (Lithium-saponified multi-purpose grease from NLGI Grade 2 in accordance with DIN 51818 TYROLIT No. 975057 Water The water pressure in the supply line must not exceed 5 bar. If necessary, use a pressure reducer. -
Page 25: Parking Brake
FSE808 6.4 Parking brake WARNING Risk of being crushed by an unsecured machine Injuries due to the machine unintentionally changing position ► Always secure the floor saw with the parking brake when the machine is not in use.. The parking brake is activated and released using your foot... -
Page 26: Setting The Handles
FSE808 Setting the handles Set the handles to the desired height and alignment for the operator. 6.7 Installing/replacing the saw blade (tool) WARNING Risk of cuts and crushing injuries The rotating saw blade or flange can catch hold of clothing or body parts and sever them. - Page 27 FSE808 NOTICE Installing Thea saw blade When installing the saw blade, make sure the surface of the blade is clean. The saw blade must lie directly against the flange. Match the rotational direction of the saw blade to the rotational direction arrow (down-cutting).
-
Page 28: Switching From Right-Hand To Left-Hand Cutting
FSE808 6.8 Switching from right-hand to left-hand cutting WARNING Risk of cuts and crushing injuries The rotating saw blade or flange can catch hold of clothing or body parts and sever them. ► Pull the plug. ► All parts must have stopped moving before working on the machine may begin. -
Page 29: Operation
FSE808 7 Operation 7.1 Safety The floor saw may only be operated by one person. Banish other persons from the work area, or create a barrier. The operator is not permitted to leave the machine while the motor is running. - Page 30 FSE808 WARNING Cut hazard Serious injuries due to a rotating saw blade or ejected parts. ► Only cut with the blade guard closed. ► Maintain a safe distance. ► Never touch the rotating saw blade. ► Wear personal protection equipment...
-
Page 31: Start Preparations
FSE808 7.2 Start preparations NOTICE Cutting without obstacles Damage to objects in the cutting area or the saw blade. ► All obstacles must be removed from the cutting area ► Ensure good lighting in the work area Make sure the cut is straight to prevent the saw blade from jamming. -
Page 32: Switching The Machine On And Off
FSE808 7.3 Switching the machine on and off NOTICE The main switch will be held in place if the unit is being supplied with power. If the switch does not remain in the I/ON position, the power is not connected. This is a... -
Page 33: Check Rotational Direction
FSE808 Switch off 1. Move the saw blade until it is free (lift the blade completely from the kerf) Activate the parking brake 2. Allow engine to cool down for 60 sec at idle speed. 3. Selection switch in the Y position 4. -
Page 34: Lower/Raise The Saw Blade And Set The Depth
FSE808 7.5 Lower/raise the saw blade and set the depth WARNING Ejected parts hazard The saw blade may be damaged if it is lowered too quickly. Segments can break out and be ejected in an uncontrolled manner. ► Slowly lower the saw blade into the cutting surface ►... -
Page 35: Relocating The Floor Saw
FSE808 7.6 Relocating the floor saw WARNING Cut hazard at rotating saw blade When touching the rotating saw blade, clothing and limbs can be pulled in and severed. ► The machine may not be maneuvered while the blade is spinning. -
Page 36: Cutting With The Saw Blade Guard Open
FSE808 7.7 Cutting with the saw blade guard open WARNING Lacerations and ejected parts hazard Severe injuries when coming into contact with the rotating saw blade or from ejected material when cutting without the saw blade guard. ► Keep the machine’s cutting area free ►... -
Page 37: Cutting Special Forms
FSE808 7.8 Cutting special forms WARNING Flush with the wall A separately available blade guard for sawing flush with a wall can be attached to the Flush-with-wall flange floor saw. To this end, the normal drive pin on the saw flange must be replaced with a shorter pin. -
Page 38: Servicing
FSE808 8 Servicing 8.1 Maintenance WARNING Cut and crush hazard Serious injuries when coming into contact with a rotating saw blade or belt drive.. ► Maintenance and repairs may only take place when the machine is switched off ► Maintenance and repairs may only be carried out by trained personnel. -
Page 39: Lubrication Points
FSE808 8.2 Lubrication points The motor must be switched off before maintenance or repair work. Secure the machine against being unintentionally reactivated. Maintenance and service work may only be carried out by qualified technical personnel. Secure the machine with a crane. -
Page 40: Check The Drive Belt Tension
FSE808 8.3 Check the drive belt tension WARNING Cut and crush hazard Body parts and clothing can be pulled in if they come into contact with the belt drive. Risk of cuts and crushing injuries through to amputations. ► Removing or opening the belt cover or reaching into the rotating belt drive is prohibited ►... -
Page 41: Replace Drive Belts
FSE808 8.4 Replace drive belts - Disconnect the power supply. - Remove the flange cover and flange Loosen the 4 mounting screws and remove the belt cover. Evenly loosen the tensioning screws on the motor slide in turns and relax the belts. -
Page 42: Troubleshooting
FSE808 8.5 Troubleshooting The motor must be switched off before maintenance or repair work. Secure the machine against being unintentionally switched back on. Maintenance and service work may only be carried out by qualified technical personnel. NOTICE The following points must be checked first in the event of cutting problems: ... -
Page 43: Circuit Diagram
FSE808 9 Circuit diagram... -
Page 44: Ec Declaration Of Conformity
FSE808 EC Declaration of Conformity Description Floor saw Type designation FSE808 We declare under our sole responsibility that this product complies with the following directives and standards: Directive applied 2006/42/EG Applied standards EN ISO 12100:2010 EN 13862:2021+A1:2009 EN 60204 -1:2018 Pfäffikon, 18.08.2023... - Page 45 TYROLIT CONSTRUCTION PRODUCTS GMBH Swarovskistraße 33 | 6130 Schwaz | Austria Tel +43 5242 606-0 | Fax +43 5242 63398 Our worldwide subsidiary companies can be found on our website at www.tyrolit.com...
Need help?
Do you have a question about the FSE808 and is the answer not in the manual?
Questions and answers