Table of contents Table of contents General information......................5 1.1 Symbols and signal words................... 5 Safety instructions......................... 6 Features............................8 Installation and starting up....................9 Connections and controls....................10 Technical specifications....................16 Plug and connection assignment................. 19 Protecting the environment................... 21 xmix 1202 FXMP USB Mixer...
Our products and documentation are subject to a process of continuous develop‐ ment. They are therefore subject to change. Please refer to the latest version of the documentation, which is ready for download under www.thomann.de. 1.1 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this document.
Safety instructions Safety instructions Intended use This device is intended to be used for amplification, mixing and playback of signals from musical instruments and microphones. Use the device only as described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage.
Page 7
Safety instructions NOTICE! Danger of short circuit due to use of unbalanced XLR cables! The device has a phantom voltage input. Using unbalanced cables with the phantom power may damage the device. Use only balanced cables. Before switching on phantom power, always make sure that no unbalanced wired cables are connected. NOTICE! Risk of fire due to installation of a wrong fuse! Using fuses of a different type than compatible with the device may cause a fire and seriously damage the device.
Features Features 10-channel mixer with built-in FX processor and USB port Bluetooth for wireless data transmission 6 mono channels (MIC, line) with 3-band EQ and low cut 2 stereo channels with balance control 1 × AUX control per channel, PRE/POST selectable Master output L/R via 2 ×...
Installation and starting up Installation and starting up Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.
Connections and controls Connections and controls Mono channel strip MIC 1 1 [MIC] | Balanced XLR mono input for connecting a microphone. 2 [LINE] | 6.3-mm jack input for connecting a line level audio source (key‐ ö boards, drum modules etc., balanced or unbalanced). 3 [80 Hz HPF] | High pass filter to attenuate rumble noise and other low-fre‐...
Page 11
Connections and controls Stereo channel strip 14, 16 [STEREO IN] | Cinch sockets for connecting stereo sources. STEREO I N REC OUT 15, 17 [REC OUT] | Line outputs with cinch sockets for connecting recording devices. 18, 19 [L] | 6.3-mm jack input for connecting the left stereo signal from a line level audio source (keyboards, drum modules etc.).
Page 12
Connections and controls Effects section, AUX 34 [PARAMETER] | Rotary control for setting the main parameter of the currently PAR AMETER selected effect. 35 [FX TO AUX] | Rotary control for adjusting the effects portion present on the [AUX SEND] output. FX TO AU X SIGNAL 36 [FX RETURN TO MIX] | Rotary control for adjusting the effects portion in the...
Page 13
Connections and controls 42 [AUX SEND] | This line level output has the signal that was set with the [AUX] channel controls and can be used, for example, to create a monitor mix. 43 [FX SEND] | This line level output has the signal that was set with the [FX] channel controls and can be sent to an external effects device, for example.
Page 14
Connections and controls +48V +48V POWER CR & P HONES (PFL) CR & P HONES 53 [+48V] LED | This LED lights up when the phantom power is on. 54 [+48V] switch | When this switch is in the ON position, a phantom voltage of 48 V is present on the XLR sockets in the mono channels for using condenser microphones.
Page 15
Back D AT E C O D E : S E R IA L N o : Thomann GmbH MAIN OUTPUTS Hans- Thomann- Str. 1 96138 B urgebrach German y Made in China C A U T I O N...
Page 18
Technical specifications Further information Built-in effects unit 19-inch rack-mountable Number of microphone channels Number of stereo inputs Number of aux paths Phantom power Built-in power supply Parametric Digital interface USB 2.0 Bluetooth Optional xmix 1202 FXMP USB Mixer...
Plug and connection assignment Plug and connection assignment Introduction This chapter will help you select the right cables and plugs to connect your valuable equipment in such a way that a perfect sound experience is ensured. Please note these advices, because especially in ‘Sound & Light’ caution is indicated: Even if a plug fits into the socket, an incorrect connection may result in a destroyed power amp, a short circuit or ‘just’...
Page 20
Plug and connection assignment XLR plug (balanced) Ground, shielding Signal (in phase, +) Signal (out of phase, –) Shielding on plug housing (option) XLR plug (unbalanced) Ground, shielding Signal Bridged to pin 1 RCA connection Drawing and table indicate the pin assignment of an RCA plug. Signal Ground, shielding xmix 1202 FXMP USB...
Repairing a device or passing it on to another user is an ecologically valuable alternative to disposal. You can return your old device to Thomann GmbH at no charge. Check the current conditions on www.thomann.de. If your old device contains personal data, delete those data before disposing of it.
Need help?
Do you have a question about the the t.mix xmix 1202 FXMP USB and is the answer not in the manual?
Questions and answers