The wireless digital controller is a compact, battery-powered unit . Three user-defined memory settings are provided for frequently used settings . As an added safety measure, WirelessOne maintains minimum air pressure of 5 PSI ( .34BAR) in the system . The manifold is also weather resistant for maximum life expectancy .
WirelessOne User Guide B. Wireless Controller Up arrow/Inflate •• (P2) Battery life indicator Bluetooth signal strength indicator ® (Indicates full or low) and connection status indicator Air pressure setting (PSI or BAR) Indicates preset Indicates when the system is inflating or...
WirelessOne User Guide PAIR THE MANIFOLD TO THE WIRELESS CONTROLLER The manifold will enter pairing mode for three minutes after the fuse is installed . Once a device is paired, it will automatically connect if no other device is already connected . The wireless controller will go into sleep mode after 40 seconds, at which time it will disconnect from the system .
WirelessOne User Guide WIRELESS CONTROLLER PRESETS 1 . Set the pressure to the desired level using the inflate and deflate buttons (Fig . B .5) . 2 . To set each preset: Preset 1: Press and hold the • (P1) for 3 seconds .
. Click on the device you want to pair . The manifold will have WirelessOne in the title (Fig . C .1 & Fig . C .2) . 4 . Once the mobile app is paired to the manifold via Bluetooth, it will connect automatically each time the manifold is active and the device is in range .
WirelessOne User Guide D. Mobile App Android User Interface 1 . When the app is open to the Menu Menu user interface, it shows the Connection status and desired pressure (Fig . D .1 & current pressure values Fig . D .2) .
WirelessOne User Guide E. Mobile App Configuration Android SETTINGS The Main Settings screen (Fig . E .1 & Fig . E .2) has these options: NOTE Settings are enabled when the check is next to the option. Devices • Lists manifolds that are within range Troubleshoot •...
Page 11
WirelessOne User Guide Settings • Pressure control units (PSI or BAR) Android • Compressor/Tank Settings - Compressor is the default setup . Select Tank if you are using an auxiliary tank and external solenoid to supply the manifold NOTE Tank mode can only be enabled or disabled through the mobile app.
WirelessOne User Guide APP PRESETS 1 . The app must be connected to the manifold to Android change presets (Fig . E .5 & Fig . E .6) . Presets are stored on the manifold, so changes made in the app will also affect the wireless controller and vice versa .
WirelessOne User Guide FIRMWARE UPDATES 1 . The phone must be connected to the internet and the Android app must be connected to the manifold to change firmware on the manifold (Fig . E .7 & Fig . E .8) .
WirelessOne User Guide F. Troubleshooting Android For any code not listed, contact Air Lift Customer Service at (800) 248-0892 or service@airliftcompany.com. Error codes are labeled “Active Errors” and “Dormant Errors” on the app (Fig . F .1 & Fig . F .2) . Active and dormant error codes are indicated by “A”...
WirelessOne User Guide TROUBLESHOOTING GUIDE Error Problem Code Potential Cause Solution If the ignition wire is not connected, the system will only maintain a preset when the vehicle starts moving or is connected to the wireless controller or mobile app.
Page 16
WirelessOne User Guide TROUBLESHOOTING GUIDE (CONTINUED) Error Problem Code Potential Cause Solution System does not Vehicle battery voltage is too low (below 9 volts) Check the vehicle battery exhaust when deflation is commanded Vehicle battery voltage is too high (above 18 volts)
Page 17
WirelessOne User Guide TROUBLESHOOTING GUIDE (CONTINUED) Error Problem Code Potential Cause Solution Unable to connect to Wireless controller batteries are low Check wireless controller battery icon. Change batteries if necessary the manifold with the (See page 20) remote Blown 15A fuse Check 15A fuse.
WirelessOne User Guide REPLACING BATTERIES IN THE WIRELESS CONTROLLER 1 . To install the two CR2032 batteries in the wireless controller, use a small flat screwdriver to separate the two halves of the controller by prying apart the internal clip locations .
WirelessOne User Guide FINDING AIR LEAKS 1 . Inflate the air springs to 30 PSI (2 .1BAR) . 2 . Spray all connections with a solution of liquid dish soap and water . Wait 30 seconds and check for bubbles which indicate leaks .
WirelessOne User Guide CUTTING AIR LINES When cutting air lines, use a sharp knife or a hose cutter and make clean, square cuts . Do not use scissors or wire cutters because these tools will deform the air line, causing it to leak around fittings .
Air Lift Company provides a 2-year Limited Warranty* to the original purchaser of WirelessOne™ from the date of original purchase, that the products will be free from defects in workmanship and materials when used on cars and trucks as specified by Air Lift Company and under normal operating conditions, subject to the requirements and exclusions set forth in the full Limited Warranty and Return Policy .
WirelessOne User Guide Replacement Part Information If replacement parts are needed, contact the local dealer or call Air Lift customer service at (800) 248-0892 . Most parts are immediately available and can be shipped the same day . Contact Air Lift Company customer service at...
Page 24
For calls outside the U .S . or Canada: (517) 322-2144 AD-946 • (052302) • ERN 9474 • JJC-0323 • Printed in the USA Air Lift Company 2727 Snow Road Lansing, MI 48917 California: WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov...
Need help?
Do you have a question about the WirelessOne and is the answer not in the manual?
Questions and answers