Table of Contents
Advertisement
Quick Links
"Graphics and specifications may change without notice".
ASSEMBLY MANUAL
Specifications:
Wing span ------------------- 63 in------------------------ 160 cm.
Wing area ------------------- 638.6 sq.in --------------- 41.2 sq.dm.
Weight ----------------------- 10.1 lbs--------------------- 4.6 kg.
Length ------------------------ 52 in ------------------------ 132 cm.
Engine ------------------ ---- 15cc.
Motor size------------------- Motor 90/ 1800watt/ ESC 100A/ Lipo
Radio ------------------------- 6 channels with 7 servos.
6s - 8s electric proprller 16x18 - 18x8.
MS: 393
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Seagull Models Art Scholl's Super Chipmunk 63 ARF 15cc
Summary of Contents for Seagull Models Art Scholl's Super Chipmunk 63 ARF 15cc
- Page 1 MS: 393 ASSEMBLY MANUAL “Graphics and specifications may change without notice”. Specifications: Wing span ------------------- 63 in------------------------ 160 cm. Wing area ------------------- 638.6 sq.in --------------- 41.2 sq.dm. Weight ----------------------- 10.1 lbs--------------------- 4.6 kg. Length ------------------------ 52 in ------------------------ 132 cm. Engine ------------------ ---- 15cc.
-
Page 2: Kit Contents
Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. INTRODUCTION. Thank you for choosing the Art Scholl's Super Chipmunk 63” ARF 15cc ARTF by SG MODELS . The was designed with the intermediate/advanced sport Art Scholl's Super Chipmunk 63” ARF 15cc flyerin mind. -
Page 3: Additional Items Required
KIT CONTENTS. HINGING THE FLAP. Fuselage Wing Set Tail Set Canopy Cowling Wing Tube Pilot Fiberglass Wheel Pants Landing Gear Tail Wheel Hardware Set ADDITIONAL ITEMS REQUIRED. 15cc gasoline engine. Computer radio 6 channels with 7 servos. Drill 1mm. Glow plug to suit engine. Propeller to suit engine. -
Page 4: Hinging The Ailerons
Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. 3) Slide the aileron on the wing panel until there is only a slight gap. The hinge is now centered on the wing panel and aileron. Remove the T-pins and snug the aileron against the wing panel. -
Page 5: Hinging The Elevator
HINGING THE ELEVATOR. Glue the rudder hinges in place using the same techniques used to hinge the ailerons. INSTALL THE AILERONS CONTROL HORN. 1) Locate the hardware necessary to install the control horns for the ailerons. Fiberglass control horn 5) Turn the wing panel over and deflect the aileron in the opposite direction from the opposite side. - Page 6 Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. Position the Control horn on the Aileron and INSTALL THE FLAP CONTROL HORN. use 30-minute Epoxy 1) Locate the hardware necessary to install the control horns for the ailerons. Fiberglass control horn Epoxy.
-
Page 7: Installing The Fuselage Servos
Rudder control horn. Rudder servo arm. Throttle servo arm. Elevator servo arm. INSTALLING THE SWITCH. INSTALLING THE FUSELAGE SERVOS. Install the switch into the precut hole in the Because the size of servos differ, you side, in the fuselage. may need to adjust the size of the precut open- ing in the mount. -
Page 8: Installing The Stopper Assembly
Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. 3) Carefully bend the second nylon tube up INSTALLING THE STOPPER at a 45º angle. his tube is the vent tube. ASSEMBLY. 4) Test it the stopper assembly into the tank. 1) Using a modeling knife, carefully cut It may be necessary to remove some of the of the rear portion of one of the 3 nylon... -
Page 9: Engine Mount Installation
Fuel tank. 8) Use plywood template to hold in place Blow through one of the lines to en- the fuel tank with C/A glue to secure the fuel sure the fuel lines have not become kinked tank inside the fuselage. inside the fuel tank compartment. -
Page 10: Mounting The Engine
Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. hread locker glue. 4mm. 3) Use a drill to drill the four holes in the engine mount rails. 4mm. MOUNTING THE ENGINE. 1) Position the engine with the drive washer (135mm) forward of the iewall as shown. - Page 11 6) Connect the Z-bend in the 450mm throttle pushrod to the outer hole of the carburetor arm. 7) Slide the throttle pushrod wire into the tube. Position the engine between the mounts. Use four M4x30mm machine screws to secure the engine to the mount as shown.
- Page 12 Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. Trim and cut. 9) Move the throttle stick to the closed po- Trim and cut. sition and move the carburetor to closed. Use a 2.5mm hex wrench to tighten the screw that secures the throttle pushrod wire.
- Page 13 M3x15mm Use a drill and drill bit to drill the holes for the cowl mounting screws. Make sure the cowl position is correct before drilling each hole. Install the muler and muler extension onto the engine and make the cutout in the cowl for muler clearance.
- Page 14 Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. Recommendation EP parts as shown (not included with your model) 4mm. - Model size: 15cc - Motor: Motor 90/ 1800watt - Propeller: 6x18 - 18x8 - ESC: 100A - Lipo Batteries: 6s - 8s 2) Attach the electric motor box to the firewall suitable with the cross lines drawn on the electric...
-
Page 15: Installing The Spinner
Epoxy. Speed control. 135mm. INSTALLING THE SPINNER. Balsa stick. Install the spinner backplate, propeller and Epoxy. spinner cone. Electric motor. Battery. The propeller should not touch any part of the spinner cone. If it does, use a sharp modeling knife and carefully trim away the spinner cone where the propeller comes in contact with it. -
Page 16: Installing The Aileron - Flap Servos
Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. 3) Apply 2-3 drops of thin C/A to each of the INSTALLING THE AILERON - FLAP SERVOS. mounting holes. Allow the C/A to cure without using accelerator. Minimum servo spec. Torque : 80 oz-in (5.8 kg-cm) @ 4.8V; 100 oz-in (7.2 kg-cm) @ 6.0V Servos. - Page 17 7) A string has been provided in the wing to pull the aileron lead through to the wing root. Remove the string from the wing at the servo location and use the tape to attach it to the servo extension lead. Pull the lead through the wing and remove the string.
-
Page 18: Installing Landing Gear
Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. 45mm. 2) Connect the linkage as shown and secure the control wire with a snap keeper. M2 lock nut. FLAP PUSHROD HORN INSTALLATION INSTALLING LANDING GEAR 1)Locate items necessary to install Spring Landing Gear. - Page 19 2) Install Spring Landing Gear into Wings. Pen. Plastic plate. Wheel Pant. Drill 2mm. Drill 1.5mm. Landing Gear. M2x10mm. M3x15mm.
- Page 20 Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. M4x5mm.
-
Page 21: Installing The Horizontal Stabilizer
3) Attach Fiberglass Wheel Pants into landing Gear. INSTALLING THE HORIZONTAL STABILIZER. 1) Using a ruler and a pen, locate the centerline of the horizontal stabilizer, at the trail- ing edge, and place a mark. Use a triangle and extend this mark, from back to front, across the top of the stabilizer. - Page 22 Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. 5) Remove the stabilizer. Using the lines you just drew as a guide, carefully remove the covering from between them using a model- Cut. ing knife. Trim and cut. 3) Slide the stabilizer into place in the pre- cut slot in the rear of the fuselage.
- Page 23 While holding the vertical stabilizer firmly in place, use a pen and draw a line on each side of the vertical stabilizer where it meets the top of the fuselage. Fill epoxy. Fill epoxy. Fill epoxy. 2) Slide the vertical stabilizer back in place.
-
Page 24: Mounting The Tail Wheel
Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. M3x12mm. MOUNTING THE TAIL WHEEL. 1) Locate the items for this section of the manual. Plastic part. Cut. C/A glue. -
Page 25: Hinging The Rudder
HINGING THE RUDDER. ELEVATOR PUSHROD HORN INSTALLATION. Glue the rudder hinges in place using the same techniques used to hinge the ailerons. 1) Install the elevator control horn using the same method as with the aileron control horns. 2) Position the elevator control horn on the both side of elevator. - Page 26 Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. Control horn. Metal clevis. M2 lock nut. Elevator pushrod. RUDDER PUSHROD HORN INSTALLATION. Elevator pushrod. 550mm.
- Page 27 If you are going to install a pilot figure, please use a sanding bar to sand the base of the figure Rudder pushrod. so that it is flat. Metal clevis. Control horn. 3) Position the pilot figure on the canopy floor as show.
-
Page 28: Apply The Decals
Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. ATTACHMENT WING-FUSELAGE. C/A glue. Attach the aluminium tube into fuselage. Wing tube. APPLY THE DECALS. 1) If all the decals are precut and ready to stick. Please be certain the model is clean and free from oily fingerprints and dust. - Page 29 2) Mount the wing to the fuselage. Using a couple of pieces of masking tape, place them on the top side of the wing back from 115mm the leading edge of the wing at the wing root. 3) Turn the airplane upside down. Place your fingers on the masking tape and carefully lift the plane .
-
Page 30: Control Throws
Instruction Manual. Art Scholl's Super Chipmunk 63” ARF 15cc. CONTROL THROWS. Rudder: Ailerons: High Rate : High Rate : Right : 50 mm Up : 30 mm Left : 50 mm Down : 30 mm Low Rate : Low Rate : Right : 40 mm Up : 20 mm... -
Page 31: Flight Preparation
FLIGHT PREPARATION. PREFLIGHT CHECK. 1) Completely charge your transmitter Check the operation and direction of the and receiver batteries before your first day of elevator, rudder, ailerons and throttle. flying. A) Plug in your radio system per the 2) Check every bolt and every glue joint in the Art Scholl's Super Chipmunk 63”...
Need help?
Do you have a question about the Art Scholl's Super Chipmunk 63 ARF 15cc and is the answer not in the manual?
Questions and answers