Page 1
MIC-3318 3U-sized CompactPCI® Intel® Pentium® 4-M Single Board Computer with VGA / Dual Giga LAN Download from Www.Somanuals.com. All Manuals Search And Download.
Page 2
All other product names or trademarks are properties of their respective owners. CE Notification The MIC-3318, developed by Advantech CO., LTD., has passed the CE test for environment specification when shielded cables are used for external wiring and sleeve core clamps are added to the USB cables.
Page 3
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
Page 4
If any of these items are missing or damaged, contact your distributor or sales representative immediately. Technical Support and Sales Assistance If you have any technical questions about the MIC-3318 or any other Advantech products, please visit our support website at: • http://www.advantech.com.tw/support For more information about Advantech’s products and sales...
Page 6
3.2 Utilities and Drivers .......... 25 3.3 USB driver ............28 3.4 Watchdog Timer (WDT) Driver ..... 28 3.4.1 Installing the Driver for the MIC-3318 Watchdog ..28 3.4.2 How to Use the MIC-3318 Watchdog Timer ....32 4. Award BIOS Setup ......35 4.1 Introduction ............
Page 7
A. Programming the Watchdog Timer 53 A.1 Overview ............54 A.2 Programming the Watchdog Timer ....54 A.3 Example Programs .......... 56 B. Pin Assignments ........65 B.1 PS/2 Keyboard and Mouse Port (1F-CN1) ... 66 B.2 CompactFlash Interface (1F-CN2) ....67 B.3 DB-15 VGA Port (1F-CN7)......
Page 8
Figure 1-6: MIC-3318 connector locations (1F) ............. 13 Figure 1-7: MIC-3318 connector locations (2F) ............. 13 Figure 1-8: MIC-3318 front panel connector and indicator locations ....14 Figure 2-1: Installing/removing the MIC-3318 into/from the chassis ....21 Figure 4-1: Initial screen of the setup program ............ 36 Figure 4-2: Standard CMOS setup screen.
MIC-3318. High Performance Intel Pentium 4 Processor-M The MIC-3318 supports the Intel Pentium 4 processor-M 1.7 GHz , with the µ-FCPGA package. The Intel Pentium 4 processor-M has on-chip 512KB L2 cache providing high performance. With the support of a 400 MHz front side bus, the MIC-3318 can fulfill customer’s expectations...
+12 V (4.75 ~ 5.25 V) @ 16mA • Operating Temperature: -10 ~ 50° C (14 ~122° F) CPU Run at 1.7 GHz -10 ~ 60° C (14 ~140° F) CPU Run at 1.2 GHz MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
• Board weight: 0.8 kg (1.8lb) • Shock: 20 G (operating); 50 G (storage/transit) • Random vibration: 1.5 Grms 1.3 Function Block Diagram Figure 1-1: MIC-3318 function block diagram Chapter 1 Hardware Configuration Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Board Dimensions 160 mm 100 mm Figure 1-2: MIC-3318 board dimensions MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
1F (means 1st floor) to represent the main board, and 2F (means 2nd floor) to represent the daughter board hereafter in this manual. Before setting the jumpers, you need to disassemble the MIC-3318 to access the component side of 1F. Figure 1-3 shows how MIC-3318 is disas- sembled/assembled. Main board...
The MIC-3318 provides jumpers for configuring your board for specific applications other than the default settings. Table 1-1 lists the jumper functions of MIC-3318. Figure 1-4 and Figure 1-5 show the locations of the jumpers. Table 1-1: MIC-3318 jumper descriptions...
1.5.3 Jumper Settings This section tells how to set the jumpers to configure your card. It gives the card default configuration and your options for each jumper. After you set the jumpers and install the card, you will also need to run the BIOS Setup program (discussed in Chapter 6) to configure the serial port addresses, floppy/hard disk drive types and system operating parameters.
IDE channel at the same time, we recommend to set the CompactFlash card as master and the other IDE drive as slave. Otherwise, the MIC-3318 may not be able to detect the CompactFlash correctly. Table 1-2: CompactFlash master/slave selection...
Table 1-3: Clear CMOS CMOS Clear Normal 1.5.6 Serial Ports (COM1 and COM2) Mode (RS-232/ 422/485) This jumper is used to set the Serial ports to act in RS-232,422 or 485 transmission mode. The transmission mode of COM1 and COM2 ports can be selected using the following settings of JP1(Pin 1 to 18) and JP2(Pin 1 to 18) respectively.
Onboard connectors link to external devices such as hard disk drives, or keyboards, etc. Table 1-5 lists the function of each connector, and Figure 1-6 and Figure 1-7 illustrate the location of each connector. Table 1-5: MIC-3318 connector descriptions Number Function 1F-CN1...
1.7 Front Panel Connectors and Indicators Figure 1-8: MIC-3318 front panel connector and indicator locations 1.8 Safety Precautions Follow these simple precautions to protect yourself from harm and the products from damage. 1. To avoid electrical shock, always disconnect the power from your PC chassis before you work on it.
1.9 Installing SDRAM (SODIMMs) The MIC-3318 provides one 200-pin SODIMM socket, which is on the component side of 1F. The socket accepts 128, 256 or 512 MB DDR. The socket can be filled with DIMMs of any size, giving a total memory capacity between 128 and 512 MB.
Page 24
MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 VGA Display Connector (1F-CN7) The MIC-3318 provides an VGA controller for a high performance VGA interface. The MIC-3318's CN7 on 1F is a DB-15 connector for VGA monitor input. Pin assignments for the VGA display are detailed in Appendix B.
3F8, 2F8, 3E8, 2E8 IRQ4/IRQ3 2F8/IRQ3 2.6 Ethernet Configuration (2F-RJ1, RJ2) The MIC-3318 is equipped with a high performance 32-bit PCI-bus Gigabit Ethernet interface which is fully compliant with IEEE 802.3u 10/ 100/1000Base-TX specifications. 2.7 USB Connector (1F-CN15, CN16) The MIC-3318 provides two USB (Universal Serial Bus) 2.0 channels via two ports on the front panel, which give complete plug and play, hot attach/detach ability for up to 127 external devices.
Improper installation of a card can easily damage the backplane of the chassis. The inject/eject handle of MIC-3318 helps you install and remove the card easily and safely. Follow the procedure below to install the MIC-...
Figure 2-1: Installing/removing the MIC-3318 into/from the chassis Chapter 2 Connecting Peripherals Download from Www.Somanuals.com. All Manuals Search And Download.
Page 30
MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
GB and larger hard drives. Furthermore, IAA enables Automatic Selection of Highest DMA Transfer Mode by the ATA/ATAPI device/ Intel chipset. This chapter will list the utilities and drivers for MIC-3318, and make a brief introduction for two of them: the USB driver and the Watchdog Timer utility.
3.2 Utilities and Drivers The following utilities and drivers are provided with MIC-3318. You can also find out the updated description of the utilities and drivers in the ReadMe.txt file on the CD-ROM. Intel Chipset Software Installation Utility Path: \Driver\Chipset\845G\ Available for the OS’s below,...
Page 34
• Microsoft Windows 2000 • Microsoft Windows XP • Win dows NT Embedded 4.0 • Windows XP Embedded • Linux • NetWare_ Novell ODI and more, on the driver CD-ROM. MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 35
USB Drivers /Utility Path: \Driver\Usb\ICH4\ Available for the OS’s below, • Microsoft Windows 98 SE • Microsoft Windows ME • Microsoft Windows 2000 • Microsoft Windows XP Hardware Monitor Utility Path: \Driver \OBS\MIC3318\ Available for the OS’s below, • Microsoft Windows 2000 •...
Intel chipsets. 3.4 Watchdog Timer (WDT) Driver In order to ensure reliable and fail-safe performance, MIC-3318 has a built-in Watchdog Timer to take care of unexpected system failures. Advantech provides the drivers and a utility to activate and configure the timer for Windows2000/XP operating systems.
Page 37
Step 2. Use Windows Explorer (or Windows Run command) to execute SETUP.EXE from the companion CD-ROM. Step 3. Click Next to proceed. Step 4. Click Next to confirm the customer information. Chapter 3 Software Configuration Download from Www.Somanuals.com. All Manuals Search And Download.
Page 38
Step 5. Select Advantech [W83627HF] Watchdog Timer and click Next to proceed. Step 6. Click Next to confirm selecting the Typical setup type. Step 7. Click Next to proceed. MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 39
Step 8. Click Finish to complete the procedure. Step 9. Click OK to restart the system and activate the Watchdog Timer. Chapter 3 Software Configuration Download from Www.Somanuals.com. All Manuals Search And Download.
3.4.2 How to Use the MIC-3318 Watchdog Timer Step 1. Open the Control Panel of the Windows and click Watchdog Service Configuration. Step 2. Click the Start Service button. Step 3. Click Setting to select the setting page. Step 4. Select the Timer Span that meets your application requirement.
Page 41
Step 5. Click Enable to enable the setting. Step 6. Check the Start watchdog service on boot to enable the Watchdog timer to start automatically after the system boots every time. Step 7. Click OK, then the configuration procedure is finished. Chapter 3 Software Configuration Download from Www.Somanuals.com.
Page 42
MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Award's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS so that it retains the Setup information when the power is turned off. MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS supports your CPU. If there is no number assigned to the patch code, please contact Advantech's application engineer to obtain an up-to-date patch code file. This will ensure that your CPU's system status is valid.
This screen allows the user to configure the board according to his particular requirements. Below are some major items that are provided in the BIOS FEATURES SETUP screen: Figure 4-.3: Advanced BIOS features setup screen MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 47
Virus Warning During and after the system boots up, any attempt to write to the boot sector or partition table of the hard disk drive will halt the system. If this happens, a warning message will be displayed. You can run the anti-virus program to locate the problem.
Page 48
Key strokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. The default is Disabled. MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 49
Typematic Rate (Chars/Sec) Set the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, 30. Typematic Delay (Msec) Sets the delay time after the key is held down before it begins to repeat the keystroke.
These registers control most of the system options in the computer. Choose the "Advanced Chipset Features" from the main menu and the following screen will appear. Figure 4-4: Advanced Chipset Features setup screen MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 51
DRAM Timing Configuration This field lets you select system memory timing data. Manual and BY SPD are two options. Default is "BY SPD" CAS Latency Time When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. The settings are: 1.5, 2 and 2.5.
Page 52
PCI memory address range dedicated for graphics memory address space. Host cycles that hit the aperture range are forwarded to the AGP without any translation. MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
On-Chip Frame Buffer Size User can select the frame buffer size. Options are 8 MB and 1 MB. 4.2.4 Integrated Peripherals Figure 4-5: Integrated Peripherals setup screens Chapter 4 Award BIOS Setup Download from Www.Somanuals.com. All Manuals Search And Download.
Page 54
Select Enabled if your system contains a Universal Serial Bus (USB) 1.1/2.0 controller. The settings are: Enabled (Default), Disabled. USB Keyboard/Mouse Support Select Enabled if you use USB KB/Mouse in DOS mode. Disabled (Default) MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 55
Init Display First User can choose display priority on either peripheral PCI slot or on board VGA chip. There are 2 options: PCI slot (Default) and On board. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read/write.
The Power Management Setup allows you to configure you system to most effectively save energy while operating in a manner consistent with your own style of computer use. Figure 4-6: Power Management Setup screen MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
ACPI Function This category allows you to select if ACPI power management are enabled or not. The options: Enabled (Default) and Disabled. 4.2.6 PNP/PCI Configuration Setup This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when commu- nicating with its own special components.
Page 58
When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. PCI/VGA Palette Snoop Leave this field at Disabled. The settings are Enabled, Disabled (Default). MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.7 PC Health Status This section shows the Status of you CPU, Fan, Warning for overall system status. This is only available if there is Hardware Monitor onboard. Figure 4-8: PC Health Status setup screen Current CPU Temp./ Vcpu-core/Vtt/+3.3V/+5V (V) This shows system health status.
4.2.11 Exit Without Saving Selecting this option and pressing the [Enter] key lets you exit the Setup program without recording any new values or changing old ones. MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
A.1 Overview The MIC-3318's watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function after the programmed period. This section describes the operation of the watchdog timer and how to program it.
Table A-1: Watchdog timer registers Address of register (2E) Attribute Description Read/Write Value (2F) description 87 (hex) ----- Write this address to I/O address port 2E (hex) twice to unlock the W83627HF 07 (hex) write Write 08 (hex) to select register of watchdog timer.
Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 65
Dec dx ; Set second as counting unit Mov al,0f5h Out dx,al Inc dx In al,dx And al,not 08h Out dx,al ;----------------------------------------------------------- Dec dx ; Set timeout interval as 10 seconds and start counting Mov al,0f6h Out dx,al Inc dx Mov al,10 Out dx,al ;-----------------------------------------------------------...
Page 66
Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 67
Dec dx ; Set minute as counting unit Mov al,0f5h Out dx,al Inc dx In al,dx Or al,08h Out dx,al ;----------------------------------------------------------- Dec dx ; Set timeout interval as 5 minutes and start counting Mov al,0f6h Out dx,al Inc dx Mov al,5 Out dx,al ;----------------------------------------------------------- Dec dx ;...
Page 68
Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 69
Dec dx ; Enable watchdog timer to be reset by mouse Mov al,0f7h Out dx,al Inc dx In al,dx Or al,80h Out dx,al ;----------------------------------------------------------- Dec dx ; lock W83627HF Mov al,0aah Out dx,al Appendix A Programming the Watchdog Timer Download from Www.Somanuals.com. All Manuals Search And Download.
Page 70
Mov al,01h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable watchdog timer to be strobed reset by keyboard Mov al,0f7h Out dx,al Inc dx In al,dx Or al,40h Out dx,al MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 71
;----------------------------------------------------------- Dec dx ; lock W83627HF Mov al,0aah Out dx,al 5. Generate a time-out signal without timer counting ;----------------------------------------------------------- Mov dx,2eh ; unlock W83627H Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al...
Page 72
Mov al,0f7h Out dx,al ;Write 1 to bit 5 of F7 register Inc dx In al,dx Or al,20h Out dx,al ;----------------------------------------------------------- Dec dx ; lock W83627HF Mov al,0aah Out dx,al MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
B.1 PS/2 Keyboard and Mouse Port (1F-CN1) Table B-1: PS/2 keyboard and mouse port pin definitions Signal 1 KB DATA 2 MS DATA 3 GND 4 VCC 5 KB CLOCK 6 MC CLOCK MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
B.3 DB-15 VGA Port (1F-CN7) Table B-3: VGA port pin definitions Signal GREEN BLUE N/C (VGAVCC) N/ C VGA_SDA HSYNC VSYNC VGA_SCL MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
B.4 USB 1.1/2.0 Ports (1F-CN15 AND 1F-CN16) Table B-4: USB 1.1/2.0 ports pin definitions Signal USB_P- USB_P+ Appendix B Pin Assignments Download from Www.Somanuals.com. All Manuals Search And Download.
B.5 COMport (2F-CN3, 2F-CN5, 2F-CN4,2F- CN6) For front panel (2F-CN3 ,2F-CN5) For external connection to 3F (2F-CN4, 2F-CN6) Table B-5: COM port pin definitions RS-232 RS-422 RS-485 NDCD NDTR NDSR NRTS NCTS MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
B.6 Parallel Port (2F-CN7,2F-CN8) For front panel (2F-CN7) For external connection to 3F(2F-CN8) Table B-6: Parallel port pin definitions Signal Signal STROBE* AUTOFD* INIT* SLCTINIT* ACK* BUSY SLCT * low active Appendix B Pin Assignments Download from Www.Somanuals.com. All Manuals Search And Download.
MDIAX1- MDIAX2+ MDIAX3+ MDIAX3- MDIAX2- MDIAX4+ MDIAX4- Table B-9: LED indicator status Mode Left Right 10Mbps Flick active/link mode 100Mbps Green Flick active/link mode 1000Mbps Orange Flick active/link mode MIC-3318 User's Manual Download from Www.Somanuals.com. All Manuals Search And Download.
Page 83
Free Manuals Download Website h p://myh66.com h p://usermanuals.us h p://www.somanuals.com h p://www.4manuals.cc h p://www.manual-lib.com h p://www.404manual.com h p://www.luxmanual.com h p://aubethermostatmanual.com Golf course search by state h p://golfingnear.com Email search by domain h p://emailbydomain.com Auto manuals search h p://auto.somanuals.com TV manuals search h p://tv.somanuals.com...