Related Manuals for WAGO Eco 2 Series
Summary of Contents for WAGO Eco 2 Series
- Page 1 WAGO Power Supply Eco 2 1-phase; 24 VDC; 10 A; 240 W 2687-2146 Product manual | Version 1.0.0 /WAGO/...
- Page 2 We wish to point out that the software and hardware terms as well as the trademarks of companies used and/or mentioned in the present manual are generally protected by trademark or patent. WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH. Product manual | Version: 1.0.0 Power Supply Eco 2...
-
Page 3: Table Of Contents
2687-2146 Table of Contents Table of Contents 1 Provisions ........................ 5 Intended Use ...................... 5 Typographical Conventions .................. 6 Legal Information ..................... 8 2 Safety .......................... 9 General Safety Regulations.................. 9 Electrical Safety ....................... 9 Mechanical Safety .................... 9 Thermal Safety ...................... 10 Indirect Safety...................... - Page 4 Table of Contents 2687-2146 Connectors ...................... 26 7.1.1 Conductor Termination ................. 26 8 Operation ........................ 28 Setting the Output Voltage via Potentiometer ............ 28 9 Notes on Operation ....................... 29 Parallel Connection .................... 29 10 Decommissioning ...................... 30 10.1 Disposal and Recycling .................. 30 11 Appendix ........................
-
Page 5: Provisions
Warranty and Liability The provisions of the latest WAGO General Terms and Conditions of Deliveries and Ser- vices (GTC) apply as well as the Software License Terms for Standard Software (SW-Li- cense) applicable to software products und software embedded in WAGO hardware prod- ucts, both available at: ü www.wago.com. -
Page 6: Typographical Conventions
Provisions 2687-2146 Obligations of Installers/Operators The installers and operators bear responsibility for the safety of an installation or a sys- tem assembled with the product. The installer/operator is responsible for the proper in- stallation and safety of the system. All laws, standards, guidelines, local regulations and accepted technology standards and practices applicable at the time of installation, and the instructions in the the products’... - Page 7 2687-2146 Provisions Figures Figures in this documentation are for better understanding and may differ from the actual product design. Warning Messages DANGER Type and source of hazard Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
-
Page 8: Legal Information
1.3 Legal Information Intellectual property The intellectual property of this document belongs to WAGO GmbH & Co. KG. The repro- duction and distribution of its content (in whole or in part) is prohibited, unless otherwise provided by statutory provisions, written agreements or this document. In case of doubt, the written consent of WAGO GmbH &... -
Page 9: Safety
• Only clamp one conductor to each connection terminal. If several conductors must be clamped, wire them using an upstream wiring assembly (e.g., WAGO Through Termi- nal Blocks). 2.3 Mechanical Safety •... -
Page 10: Thermal Safety
• Clean tools and materials are imperative for handling the product. • The product contains no parts that can be serviced by the user. Always have all ser- vice, maintenance and repair work performed by specialists authorized by WAGO. • Replace any defective or damaged devices. -
Page 11: Properties
Properties 3 Properties 3.1 Overview The WAGO Power Supplies Eco 2 Series 2687 are switched mode Power supplies with a wide range of uses. They include all important basic functions and are available in differ- ent performance classes and widths. The Power supplies are fitted on a DIN-rail. With their slim design, they are suitable for use both in the control cabinet and in a compact distribution box. - Page 12 Properties 2687-2146 Front side Type Plate 8 Type label [} 13] LED indicator 8 Indicators [} 15] 8 Setting the Output Voltage via Potentiometer Potentiometer for setting the output voltage [} 28] QR code Marker carrier 8 Accessories [} 31] Input X1 (L N PE) 8 Terminal Blocks [} 13] Latch for mounting to /removal from DIN rail Product manual | Version: 1.0.0 Power Supply Eco 2...
-
Page 13: Product Identification
8 Guidelines, approvals and standards [} 20] Label with product-specific information 3.4 Connections 3.4.1 Terminal Blocks The supply lines are connected on the input and output side using the WAGO PCB termi- nal blocks with levers: • Input side: 3-pole • Output side: 7-pole Product manual | Version: 1.0.0... -
Page 14: Terminations - Input Side
Properties 2687-2146 Note the maximum permissible connection cross-sections of the power cables (see Sprungziel: Ansicht). 8 Type Check the associated operating voltage before connecting the equipment (see label [} 13]). Additional information on the connection technology is available in Section Connection. 3.4.1.1 Terminations – Input Side Figure 3: Terminations –... -
Page 15: Control Elements
2687-2146 Properties 3.5 Control Elements The control elements are described below. For information on using these controls, see 8 Operation [} 28]. 3.5.1 Potentiometers A potentiometer is located on the front of the product for setting or adjusting the output voltage. The potentiometer can be used to set the output voltage between 23 … 28 VDC. Figure 5: Potentiometer 3.6 Indicators The indicators are located on the front of the product. -
Page 16: Input
Properties 2687-2146 137 mm 50 mm 130 mm Figure 7: Dimensions Note Observe mounting position! 8 Mounting The following electrical data refers to the nominal mounting position (see Positions and Clearances [} 21]). 3.7.2 Input Table 2: Technical Data – AC Input Property Value Nominal input voltage 1 x 100 … 240 VAC Input voltage range... -
Page 17: Output
2687-2146 Properties Property Value Holding time, typ. 100 VAC ≥ 35 ms 230 VAC ≥ 35 ms At nominal load. Table 5: Technical Data – Input Side Connection Property Value Connection type 2604 Series Querschnitt Solid 0.2 … 4 mm² / 24 … 12 AWG Fine-stranded 0.2 … 4 mm² / 24 … 12 AWG Insulated ferrule with plastic collar 0.25 … 2.5 mm² / 22 … 14 AWG Insulated ferrule without plastic collar 0.25 … 2.5 mm² / 22 … 14 AWG Strip length... -
Page 18: Efficiency/Power Loss
Properties 2687-2146 3.7.4 Efficiency/Power Loss Table 8: Technical Data – Efficiency/Power Loss Property Value Efficiency, typ. 100 VAC Still missing 230 VAC 93 % Power loss, typ. 100 VAC < 1.3 W (no load), ≤ 29 W (nominal load) 230 VAC < 3 W (Leerlauf). ≤ 13 W (nominal load) At nominal load. -
Page 19: Environment Requirements
2687-2146 Properties 3.7.6 Environment requirements Table 10: Technical Data – Environment requirements Property Value Ambient temperature, operation −25 … +70 °C (Start-up at −40 °C; type-tested for ≥ 120 VAC) Derating (temperature-dependent) −3 %/K (> +45 °C) Relative humidity 5 … 96 % (no condensation permissible) Ambient temperature, storage −40 … +85 °C Relative humidity, storage (without 5 … 96 % (no condensation permissible) condensation) Temperature coefficient... -
Page 20: Guidelines, Approvals And Standards
25 °C and 75 % relative humidity. Type testing / 60 s 3.8 Guidelines, approvals and standards The applicable guidelines, approvals and standards for the product can be found on the product detail page at:ü www.wago.com/2687-2146. Product manual | Version: 1.0.0 Power Supply Eco 2... -
Page 21: Planning
2687-2146 Planning 4 Planning 4.1 Mounting Positions and Clearances Table 13: Technical Data – Minimum Clearances Mounting Direc- Front Side Clearance from tions Front Back Bottom Left Right Vertical Front 70 mm 70 mm 70 mm 6 mm 6 mm Horizontal 70 mm 70 mm 70 mm... -
Page 22: Short-Circuit And Overload Behavior
Planning 2687-2146 Table 15: Derating (Temperature-Dependent) Ambient Temperature Derating > +45 °C −3 %/K (> +45 °C) 10,0 T [°C] -25 -20 -15 -10 -5 Figure 10: Derating (Temperature-Dependent) 4.6 Short-Circuit and Overload Behavior The output of the product is electronically protected against overload and short circuit. The following values apply to the description below: •... - Page 23 2687-2146 Planning Input Voltage Output Voltage Switch-on Time Figure 12: Turn-on time After eliminating the overload or short circuit, the product automatically supplies the out- put voltage as indicated. Product manual | Version: 1.0.0 Power Supply Eco 2...
-
Page 24: Transport And Storage
Transport and Storage 2687-2146 5 Transport and Storage The original packaging offers optimal protection during transport and storage. • Store the product in suitable packaging, preferably the original packaging. • Only transport the product in suitable containers/packaging. • Make sure the product contacts are not contaminated or damaged during packing or unpacking. -
Page 25: Installation And Removal
2687-2146 Installation and Removal 6 Installation and Removal The product can either be mounted on a DIN-35 rail or alternatively by means of a screw mount. 6.1 DIN-35 Rail 8 Technical data The DIN rail is located in the center of the vertical axis (see [} 15]). -
Page 26: Connection
7.1 Connectors 7.1.1 Conductor Termination If multiple conductors must be laid on one connection, connect them in an upstream wiring assembly, e.g., using WAGO Through Terminal Blocks. Direct Insertion of Conductors The following conductors can be inserted directly without tools: • Fine-stranded conductors with ferrules and plastic collars for all permissible cross-sec- tions •... - Page 27 If more than one conductor needs to be routed to one connection, connect them in an up- circuit wiring assembly – for example, using WAGO through terminal blocks. Product manual | Version: 1.0.0...
-
Page 28: Operation
Operation 2687-2146 8 Operation 8.1 Setting the Output Voltage via Potentiometer 8 Control Elements The potentiometer (see [} 15]) on the front of the product can be used to set the output voltage in the range of 23 … 28 VDC: • Turning clockwise increases the output voltage. •... -
Page 29: Notes On Operation
2687-2146 Notes on Operation 9 Notes on Operation 9.1 Parallel Connection In parallel operation, set the output voltage of the products that will be connected in paral- lel to precisely the same value, if possible. The resistance of the conductors between the product and the load must be nearly identical. -
Page 30: Decommissioning
Decommissioning 2687-2146 10 Decommissioning 10.1 Disposal and Recycling WEEE Mark Electrical and electronic equipment may not be disposed of with household waste. This also applies to products without this mark. Electrical and electronic equipment contain materials and substances that can be harmful to the environment and health. -
Page 31: Appendix
2687-2146 Appendix 11 Appendix 11.1 Accessories Details on accessories are available online at ü www.wago.com. The following accessories are available for the product: Accessories – Tools Table 16: Accessories – Tools Description Name Item Number Operating tool for setting the potentiometer Screwdriver PH0 210-769 Accessories –... - Page 32 Appendix 2687-2146 ® • EnOcean is a registered trademark of EnOcean GmbH. • Google Play is a registered trademark of Google Inc. • IO-Link is a registered trademark of PROFIBUS Nutzerorganisation e.V. ® • KNX is a registered trademark of the KNX Association cvba. ®...
- Page 33 2687-2146 List of Tables List of Tables Table 1 Technical Data – Product....................Table 2 Technical Data – AC Input ....................Table 3 Technical Data – Inrush Current ..................Table 4 Technical Data – Mains Failure Buffering Time ..............Table 5 Technical Data –...
- Page 34 List of Figures 2687-2146 List of Figures Figure 1 View ..........................Figure 2 Type Plate........................Figure 3 Terminations – Input Side ..................... Figure 4 Terminations – Output Side ..................Figure 5 Potentiometer ....................... Figure 6 LED "Overload" and LED "DC OK"................Figure 7 Dimensions ........................
- Page 35 2687-2146 List of Figures Product manual | Version: 1.0.0 Power Supply Eco 2...
- Page 36 WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH. Copyright – WAGO GmbH & Co. KG – All rights reserved. The content and structure of the WAGO websites, catalogs, videos and other WAGO media are subject to copyright. Distri- bution or modification of the contents of these pages and videos is prohibited. Furthermore, the content may neither be copied nor made available to third parties for commercial pur-...