Etekcity EK8060 - Digital Kitchen Scale Manual

Package Contents

1 x Digital Kitchen Scale
2 x 3V CR 2032 Batteries (Pre-Installed)
1 x Quick Start Guide

Specifications

Function Diagram

1. Unit Selection Button
2. LCD Display
3. Power/Tare Button
4. Battery Compartment
5. Screw
6. Anti-Skid Pads

Symbols

Solids

Water (Liquid)

Milk (Liquid)

Using Your Scale

Note:

• For accurate results, always place the scale on a hard, dry, flat surface, and keep the scale away from dirt, dust, vibrations, wind, air currents, and electromagnetic interference.
• When you turn on the scale, choose units, or use the tare function, wait for the display to read before measuring.
• The batteries are pre-installed in the scale. Turn the scale over and pull the plastic strip out from the battery compartment.

General Operation

1. Place the scale on a hard, flat, level surface.
2. Press to turn on the scale. Make sure the display reads . Press UNIT to select your desired measuring unit, which will show at the bottom of the display.
3. Place your item on the scale.
4. Wait for the reading on the display to stabilize.

Zero / Tare Function

Whenever you measure items inside a container, you can use the tare function to remove the container's weight from the final measurement.

1. Press to turn on the scale. Make sure the display reads . If the screen does not display automatically, press to adjust to zero.
2. Place the container on the center of the scale.
3. Wait for the reading on the display to stabilize. The display will show the container's weight.
4. Press to tare the weight of the container. The screen should now display .
5. Place the liquid or items into the container. The scale will measure the contents without including the weight of the container. [Figure 1.1]
   
6. When you're done, reset the scale by removing all weight and pressing again.

Unit Conversion

To change the unit of measurement, press UNIT until the display shows the desired unit of measurement.

Automatic Power Off

To save battery power, the scale will automatically power off after 180 seconds of inactivity.

Manual Power Off

Press and hold for 2 seconds to turn off the scale.

Replacing the Batteries

1. Turn the scale over and use a screwdriver to loosen the screw of the battery compartment.
2. Take out the used batteries and replace them with 2 new 3V CR2032 batteries.
3. Replace the battery compartment cover and screw it shut.

Troubleshooting

Problem	Possible Solution
Scale does not turn on.	Open the battery compartment cover and remove the plastic strip.
	Replace the batteries.
	Make sure batteries are inserted under the correct polarity as marked in the battery compartment.
Reading is inaccurate.	Place the scale on a hard, dry, and flat surface.
	Make sure the screen displays before measuring (see Zero / Tare Function).
	Remove the batteries for 45 seconds, then replace them to reset the scale.
Display shows	Item is too heavy. Remove item from scale to protect its weight sensors. Use a different scale with a higher weight range.
Display shows	Calibration error. Turn the scale off and on again. Avoid moving the scale while measuring.
Display shows	Battery power is low. Replace the batteries.

If your problem is not listed, please contact Customer Support.

Customer Support

If you have any questions or concerns about your new product, please contact our helpful Customer Support Team.

CUSTOMER SUPPORT

Etekcity Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806

Email: support@etekcity.com

SUPPORT HOURS

Toll-Free: (855) 686-3835
Mon–Fri, 9:00 am–5:00 pm PST/PDT

*Please have your order invoice and order ID ready before contacting Customer Support.

READ AND SAVE THESE INSTRUCTIONS

Important Safety Information

To avoid damage to this scale, please read and follow all instructions and safety guidelines in this manual.

Scale

• Always place the scale on a hard, dry, and flat surface before measurement in order to ensure accuracy.
• Do not exceed the 11 lb / 5000 g weight capacity as it will damage the scale. An error indicator will appear on the LCD display if the limit is exceeded.
• Do not immerse the scale in water or any liquid. If liquid is spilled on the digital display or buttons, immediately wipe the scale dry with a soft cloth to avoid internal damage.
• Handle with care. This scale is not intended for commercial or heavy-duty use.
• Keep the scale in a cool, dry place. Avoid exposure to damp environments or extreme temperatures.
• Household use only.

Batteries

• Do not mix new and old batteries.
• If the low battery indicator " " appears on the display, replace the batteries.
• If the scale is not in use for an extended period of time, remove the batteries to conserve battery life and extend the lifetime of the scale.