Etekcity EK4150 Series - Digital Kitchen Scale Manual

Specifications

Function Diagram

1. Stainless Steel Bowl
2. Digital Scale
3. Tare / Increase Timer
4. Unit Selection / Decrease Timer

5. Digital Display
6. On/Off
7. Set Timer
8. Battery Compartment

Digital Display

1. Timer
2. Temperature
3. Measurement Unit
4. Timer Set
5. Tare Function
6. Negative Weight Value
7. Zero Function
8. Weight Measurement

Setup

1. Open the battery compartment on the underside of the scale.
2. Remove the insulation strip. [Figure 1.1]
   
3. Replace the battery cover.
4. Press the ON/OFF button to turn on the scale.

Operation

Tips

• For accurate results, always place the scale on a hard, dry, flat surface, and keep the scale away from dirt, dust, vibrations, wind, air currents, and electromagnetic interference.
• When you turn on the scale, choose units, or use the tare function, always wait for the scale to read "0.0" before measuring.

Note: The scale will automatically shut off after 2 minutes of inactivity.

General Operation

1. Place the scale on a hard, flat, level surface for measurement.
2. Press ON/OFF to turn on the scale. Make sure the display shows Press UNIT to select your desired measuring unit.
3. Place your item on the scale.
4. Wait for the reading on the display to stabilize.

Note:

• If you're using the bowl or another container to hold the items or liquid you're measuring, first place the empty container on the scale. Press Z / T to tare the container's weight (see Tare Function).
• To reset the scale, remove all weight from the platform and press Z / T.

Zero / Tare Function
Whenever you measure liquid or other items inside the included bowl, you can use the tare function to remove the bowl's weight from the final measurement. You can also use other containers in place of the bowl.

1. Place the bowl on the scale. The display will show the bowl's weight.
2. Press Z / T. The display will show "O" again. [Figure 2.1]
   
3. Place liquid or items in the bowl. The scale will measure the liquid or items without including the weight of the bowl. [Figure 2.2]
   
4. When you're done, reset the scale by removing all weight and pressing Z / T again.

Timer Function

1. Press T-SET.
2. Set the numbers from left to right, using Z / T to increase and UNIT to decrease values. Press T-SET to confirm the selection for each time. The press of T-SET after the last selection will confirm and start the timer.
3. When the timer counts down to "00:00", the digital scale will sound an alarm for 70 seconds.
4. Press any button to stop the alarm. To stop the timer at any time, press the T-SET button.

Note: The maximum amount of time you can set the timer for is 99 minutes and 59 seconds.

Battery Replacement

1. Open the battery compartment on the underside of the scale.
2. Take out the old batteries and replace them with new 1.5V AAA batteries.
3. Replace the battery compartment cover.

Troubleshooting

Important Safety Information

To avoid damage to this scale, please read and follow all instructions and safety guidelines in this manual.

Scale

• Always place the scale on a hard, dry, and flat surface before measurement in order to ensure accuracy.
• Do not exceed the 176 oz / 11lb / 5000 g / 5 kg weight capacity as it will damage the scale. An error indicator will appear on the LCD display if the limit is exceeded. Do not immerse the scale in water or any liquid. If liquid is spilled on the digital display or buttons, immediately wipe the scale dry with a soft cloth to avoid internal damage.
• Handle with care. This scale is not intended for commercial or heavy-duty use.
• Keep the scale in a cool, dry place. Avoid exposure to damp environments or extreme temperatures.
• Household use only.

Batteries

• Do not mix new and old batteries.
• If the low battery indicator ("Lo") appears on the display, replace the batteries.
• If the scale is not in use for an extended period of time, remove the batteries to conserve battery life and extend the lifetime of the scale.

Connect with us @Etekcity