Etekcity EKS-L221-SUS - Luminary Kitchen Scale Manual

Also See for EKS-L221-SUS:

User manual (17 pages)

User manual (17 pages)

Table of Contents

Contents

1 Package Contents
2 Specifications
3 Function Diagram
4 Display Diagram
5 Using Your Device
6 Troubleshooting
7 Important Safety Information
8 Warranty Information
9 Customer Support
10 Documents / Resources
- 10.1 Download manual

Etekcity EKS-L221-SUS - Luminary Kitchen Scale Manual

Package Contents

1 x Luminary Kitchen Scale
1 x USB Charging Cable
1 x Quick Start Guide

Specifications

Models	EKS-L221-SUS, EKS-L221-BUSR
Weight Capacity	353 oz / 22 lb / 10 kg / 10000 mL
Units	oz / lb: oz / g / mL (water/milk) / fl'oz (water/milk)
Increments	0.05 oz / 1 g
Auto-Off	180 seconds
Battery	300mAh Li-ion Battery
Input	5.0V 500mA (USB Type-C Charging)
Dimensions	9.1 x 6.7 x 1.1 in / 230 x 170 x 27 mm

Function Diagram

LED Display
Unit Selection Button
Power/Zero Button
Locking Key (Hold Button)
USB Charging Port
Anti-Skid Pads

Display Diagram

Battery Indicator
Milk
Water (Liquid)
Tare Indicator
Weight Value
Measurement Unit
Hold Indicator

Using Your Device

Note:

For accurate results, always place the scale on a hard, flat surface, and keep the scale away from dirt, dust, vibrations, wind, air currents, and electromagnetic interference.
When you turn on the scale, choose units, or use the tare function, wait for the display to read "0.00" before measuring.

General Operation

Place the scale on a hard, flat surface.
Tap to turn on the scale. Make sure the display reads "0.00".
Tap UNIT to select your desired measuring unit, which will show on the right of the display.
Note: Optionally, press and hold UNIT to quickly switch between units.
Place your item on the scale.
Wait for the reading on the display to show.
When you're done, reset the scale by removing all items from the scale. If the display doesn't read "0.00", press to reset the weight to zero.

Zero/Tare Function

Whenever you measure items inside a container, you can use the tare function to remove the container's weight from the final measurement.

Tap to turn on the scale. Make sure the display reads "0.00". If the screen does not display "0.00" automatically, tap to adjust to zero.
Place the container on the center of the scale.
Wait for the reading on the display to show the container's weight.
Tap to tare the weight of the container. The screen will now display "0.00".
Place the liquid or items into the container. The scale will measure the contents without including the weight of the container.
When you're done, reset the scale by removing all weight and tapping again.

Unit Conversion

To change the unit of measurement, tap UNIT until the display shows your desired unit of measurement.
Optionally, press and hold UNIT to quickly switch between units.

Hold Function

Tap HOLD to lock the measurement data on the display. Tap HOLD again to unlock the display.
Note: In hold mode, will not work. You can still use UNIT to switch between units.

Automatic Power Off

To save battery power, the scale will automatically power off after 180 seconds of inactivity.

Manual Power Off

Tap and hold for 2 seconds to turn off the scale.

Battery

While the scale is in use, will flash if the scale is running low on battery. The scale's display will show "Lo" when the battery needs to be charged immediately. Follow the steps to recharge the battery.

Insert the USB charging cable into the USB charging socket.
Plug the USB charging cable into a DC 5V adapter and plug into an outlet. You can also plug the cable into a powered USB outlet.
When charging, will flash. Once the battery is fully charged, will stop flashing.

Note:

The scale can't be used while charging, so it is recommended to charge the battery when flashes, indicating low battery.

Maintenance

Use a slightly damp cloth to clean the surface of the scale, followed by a dry, soft cloth to wipe away the remaining moisture.
Use a dry, soft cloth to wipe dust off the scale.
Do not wash the scale or immerse it in water or any other liquid.

Troubleshooting

Problem	Possible Solution
The unit does not turn on	The scale may need to be charged. Plug in the USB power cord to charge.
Reading is inaccurate	Place scale on a level surface.
	Keep scale away from dirt, dust, vibrations, wind, air currents, and electromagnetic interference.
	Make sure the screen displays "0.00" before measuring (see Zero/Tare Function).
Display shows Err	Item is too heavy. Remove item from scale to protect its weight sensor. Use a different scale with a higher weight range.
Battery Indicator is flashing	A flashing while the scale is in use means the battery is low. It is recommended to charge the battery. A flashing while charging means the scale is still charging and will stop flashing when the battery is fully charged.
Display shows Lo	The battery is out of power and needs to be charged immediately. Plug in the USB power cord to charge the scale (see Battery).

If your problem is not listed, please contact Customer Support (see below.

Important Safety Information

Please read and follow all instructions and safety guidelines in this manual.

Scale

Do not exceed the 22 lb / 10 kg weight capacity, as it will damage the scale. An error indicator will appear on the LED display if the limit is exceeded.
Do not immerse the scale in water or any liquid. If liquid is spilled on the digital display or buttons, immediately wipe the scale dry with a soft cloth to avoid internal damage.
The scale is IPX6 water resistant, which means it can withstand most liquid spills without permanent damage. However, we still recommend wiping the scale dry with a soft cloth after any spills to keep it in optimal condition.
Handle with care. This scale is not intended for commercial or heavy-duty use.
Keep the scale in a cool, dry place. Avoid exposure to damp environments or extreme temperatures.
Household use only.

SAVE THESE INSTRUCTIONS