J5 & J6 - Expansion Connector Cable Details - FDI UEZGUI-4357-50WVN-BA User Manual

Pin Pin Name
1 Ground (GND)
2 GPIO6.30/CTOUT12
3 GPIO4.10/QEI_PHA
4 GPIO6.28/CTOUT11
5 GPIO6.27/CTOUT13
6 GPIO6.26/CTOUT10
7 GPIO6.25/CTOUT14
8 GPIO6.24/CTIN1
9 GPIO5.17/MCOB0/RXD3
10 GPIO4.15/MCOA0/TXD3
11 GPIO4.9/QEI_PHB/RXD2
12 GPIO4.8/QEI_IDX/TXD2
13 5volts(5VO)
14 Ground (GND)
15 GPIO3.13/CTOUT12/ADC0.3
16 GPIO3.12/CTOUT13/ADC0.4
17 GPIO7.22/ADC0.2/U0_CLK/CTIN2
18 GPIO7.20/ADC1.3/U3_DIR/SSP1_MISO
19 GPIO7.19/ADC1.4/U3_UCLK/SSP1_SSEL
20 Ground (GND)
J5 & J6 - Expansion Connector Cable Details
The maximum length for the expansion connector cables is as follows:
General Purpose IO, TTL, Serial, 6" recommended maximum, 8" absolute maximum
3/27/2024
µ E Z G U I U s e r ' s M a n u a l
J5 Signal Details
GPIO6.30 – General Purpose I/O
CTOUT12 – SCT output 12, Match output 3 of timer 3
GPIO4.10 – General Purpose I/O
Quadrature Encoder Interface Phase A Input
GPIO6.28 – General Purpose I/O
CTOUT11 - SCT output 11. Match output 3 of timer 2.
GPIO6.27 – General Purpose I/O
CTOUT13 - SCT output 13. Match output 3 of timer 3.
GPIO6.26 – General Purpose I/O
CTOUT10 - SCT output 10. Match output 3 of timer 3.
GPIO6.25 – General Purpose I/O
CTOUT14 – SCT Output 14, Match output 2 of timer 3
GPIO6.24 – General Purpose I/O
CTIN1 – SCT Input 1, Capture input 1 of timer 0, Capture input 1 of timer 2
GPIO5.17 – General Purpose I/O
MCOB0 – Motor Control PWM Channel 0, output B
RXD3 – UART Channel 3 Receive Data
GPIO4.15 – General Purpose I/O
MCOA0 – Motor Control PWM Channel 0, output A
TXD3 – UART Channel 3 Transmit Data
Quadrature Encoder Interface Phase B Input
RXD2 – UART Channel 2 Receive Data
Quadrature Encoder Interface INDEX Input
TXD2 – UART Channel 2 Transmit Data
GPIO3.13 – General Purpose I/O
CTOUT12 – SCT output 12, Match output 0 of timer 3
ADC0.3 – ADC0 Channel 3 input
GPIO3.12 – General Purpose I/O
CTOUT13 – SCT output 13, Match output 1 of timer 3
ADC0.4 – ADC0 Channel 4 input
GPIO7.22 – General Purpose I/O
ADC0.2 – ADC0 Channel 2 input
U0_CLK – UART Channel 0 Synchronous Clock I/O
GPIO7.20 – General Purpose I/O
ADC1.3 – ADC1 Channel 3 input
U3_DIR – UART Channel 3 RS485 output enable/direction
SSP1_MISO – SPI Channel 1 Master Input/Slave Output
GPIO7.19 – General Purpose I/O
ADC1.4 – ADC1 Channel 4 input
U3_CLK – UART Channel 3 Synchronous Clock I/O
SSP1_SSEL – SPI Channel 1 Slave Select
Copyright ©2024, Future Designs, Inc.
Pin Description
GPIO4.9 – General Purpose I/O
GPIO4.8 – General Purpose I/O
5.0 Volts
P a g e | 27
Power
I/O
O
I/O
I
I/O
O
I/O
O
I/O
O
I/O
O
I/O
I
I/O
O
I
I/O
O
O
I/O
I
I
I/O
I
O
Power
Power
I/O
O
I
I/O
O
I
I/O
I
I/O
I/O
I
I/O
I/O
I/O
I
I/O
I/O
Power
Revision 1.4