FDI UEZGUI-4357-50WVN-BA User Manual page 26

Pin Pin Name
9 GPIO6.12/TXD1
10 Ground (GND)
11 USB1_DM
12 USB1_DP
13 GPIO5.5/CTIN2/T3_MAT2/USB1_VBUS
14 GPIO4.11/MCOB1/USB1H_OVC/RXD0
15 GPIO5.18/MCOA1/USB1H_PPWR/TXD0
16 GPIO4.14/MCOB2/I2STX_SDA/MOSI0
17 GPIO4.13/MCOA2/I2STX_WS/MISO0
18 I2STX_SCK/SSP0SCK
19 GPIO5.9/I2SRX_SDA/CAN0TD
20 GPIO5.8/I2SRX_WS/CAN0RD
21 I2SRX_SCK
22 Ground (GND)
23 RESET_INn
24 RESET_OUTn
25 GPIO2.4/DAC/CTOUT2
26 GPIO2.1/ADC0.1/CTOUT1
GPIO0.12/ENET_MDIO/U2_UCLK/
27
T0_CAP3/CAN1_TD
3/27/2024
µ E Z G U I U s e r ' s M a n u a l
RXD1 – UART Channel 1 Receive Data
GPIO6.12 – General Purpose I/O
TXD1 – UART Channel 1 Transmit Data
USB_D- 1 - USB port 1 bidirectional D- line.
USB_D+1 - USB port 1 bidirectional D+ line.
CTIN2 – SCT input 2. Capture input 2 of timer 0
T3_MAT2 – Match output 2 of timer 3
USB1_VBUS – USB Channel 1 VBus input
GPIO4.11 – General Purpose I/O
MCOB1 – Motor Control PWM Channel 1 output B
USB1H_OVC – USB Channel 1 Power Fault (same as USB1_PWR_FAULT)
RXD0 – UART Channel 0 Receive Data
GPIO5.18 – General Purpose I/O
MCOA1 – Motor Control PWM Channel 1 output A
USB1H_PPWR – USB Channel 1 Host VBus Drive Signal
TXD0 – UART Channel 0 Transmit Data
GPIO4.14 – General Purpose I/O
MCOB2 – Motor Control PWM Channel 2 output B
I2STX_SDA – I2S Audio Transmit Serial Data
MOSI – SPI Channel 0 Master Output, Slave Input Serial Data
GPIO4.13 – General Purpose I/O
MCOA2 – Motor Control PWM Channel 0 output A
I2STX_WS – I2S Audio Transmit Word Select
MISO0 – SPI Channel 0 Master Input, Slave Output Serial Data
Connected to pin F13 of LPC4357 BGA (P3_0)
I2STX_SCK – I2S Audio Transmit Clock
SSP0SCK – SPI Channel 0 Serial Clock
I2SRX_SDA – I2S Audio Receive Serial Data
CAN0TD – CAN Channel 0 Transmit Data
I2SRX_WS – I2S Audio Receive Word Select
CAN0RD – CAN Port 0 Receive Data
Connected to pin M12 of LPC4357 BGA (P6_0)
I2SRX_SCK – I2S Audio Receive Clock
External reset input: A LOW on this pin resets the device, causing I/O ports and peripherals to
take on their default states, and processor execution to begin at address 0.
TTL with hysteresis, 5 V tolerant
RSTOUT - This is a 3.3 V pin. LOW on this pin indicates LPC4357 being in Reset state
CTOUT2 – SCT Output 2, Match output 2 of timer 0
ADC0.1 – ADC0 & ADC1, input channel 1
CTOUT1 – SCT Output 1, Match output 3 of timer 3
GPIO0.12 – General Purpose I/O
ENET_MDIO – Ethernet MIIM data input and output
U2_UCLK – UART Channel 2 Serial Clock input/output
T0_CAP3 – Capture input 3 of timer 0
Copyright ©2024, Future Designs, Inc.
Pin Description
GPIO5.5 – General Purpose I/O
GPIO5.9 – General Purpose I/O
GPIO5.8 – General Purpose I/O
GPIO2.4 – General Purpose I/O
DAC – DAC Output
GPIO2.1 – General Purpose I/O
P a g e | 25
I
I/O
O
Power
I/O
I/O
I/O
I
O
I
I/O
O
I
I
I/O
O
O
O
I/O
O
I/O
I/O
I/O
O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
I/O
I
I
I
Power
I
O
I/O
O
O
I/O
I
O
I/O
I/O
I/O
I
Revision 1.4