Makita RP001G Instruction Manual page 19

3. Place the tool on the templet and move the tool so
that the templet guide slides along the side of the templet.
► Fig.40
► Fig.41: 1. Router bit 2. Base 3. Templet
4. Workpiece 5. Distance (X) 6. Outside
diameter of the templet guide 7. Templet
guide
NOTE: The workpiece will be cut a slightly different
size from the templet. Allow for the distance (X)
between the router bit and the outside of the templet
guide. The distance (X) can be calculated by using
the following equation:
Distance (X) = (outside diameter of the templet guide
- router bit diameter) / 2
Using the trimmer guide
Optional accessory
The trimmer guide allows for trimming the curved side
like veneers for furniture by moving the guide roller
along the side of the workpiece.
► Fig.42: 1. Trimmer guide 2. Rod 8 3. Guide holder
1. Install the trimmer guide and rods to the guide
holder.
2. Insert rods to the slots in the guide holder and
tighten the clamping screw.
3.
Loosen the clamping screw and adjust the dis-
tance between the router bit and the trimmer guide by
turning the adjusting screw (1.5 mm per turn). At the
desired distance, tighten the clamping screw to secure
the trimmer guide.
4. Move the tool with the guide roller riding the side
of the workpiece.
► Fig.43: 1. Router bit 2. Guide roller 3. Workpiece
Dust nozzle
Installing the dust nozzle enables to connect a Makita
vacuum cleaner to the tool.
1.
Install the dust nozzle on the tool base using the
thumb screw so that protrusion on the dust nozzle fit to
the notch in the tool base.
► Fig.44: 1. Dust nozzle 2. Thumb screw 3. Notch
2. Connect a Makita vacuum cleaner to the dust
nozzle.
► Fig.45
WIRELESS ACTIVATION
FUNCTION
What you can do with the wireless
activation function
The wireless activation function enables clean and com-
fortable operation. By connecting a supported vacuum
cleaner to the tool, you can run the vacuum cleaner
automatically along with the switch operation of the tool.
► Fig.46
To use the wireless activation function, prepare follow-
ing items:
• A wireless unit (optional accessory)
• A vacuum cleaner which supports the wireless
activation function
The overview of the wireless activation function
setting is as follows. Refer to each section for detail
procedures.
1.
Installing the wireless unit
2.
Tool registration for the vacuum cleaner
3. Starting the wireless activation function
Installing the wireless unit
Optional accessory
CAUTION:
Place the tool on a flat and stable
surface when installing the wireless unit.
NOTICE:
Clean the dust and dirt on the tool
before installing the wireless unit. Dust or dirt
may cause malfunction if it comes into the slot of the
wireless unit.
NOTICE:
To prevent the malfunction caused by
static, touch a static discharging material, such
as a metal part of the tool, before picking up the
wireless unit.
NOTICE:
When installing the wireless unit,
always be sure that the wireless unit is inserted
in the correct direction and the lid is completely
closed.
1. Open the lid on the tool as shown in the figure.
► Fig.47: 1. Lid
2. Insert the wireless unit to the slot and then close
the lid.
When inserting the wireless unit, align the projections
with the recessed portions on the slot.
► Fig.48: 1. Wireless unit 2. Projection 3. Lid
4. Recessed portion
When removing the wireless unit, open the lid slowly.
The hooks on the back of the lid will lift the wireless unit
as you pull up the lid.
► Fig.49: 1. Wireless unit 2. Hook 3. Lid
After removing the wireless unit, keep it in the supplied
case or a static-free container.
NOTICE:
Always use the hooks on the back of
the lid when removing the wireless unit. If the
hooks do not catch the wireless unit, close the lid
completely and open it slowly again.
19 ENGLISH