EGO PRO X CSX5000 Manual page 11

operation under heavy load, which can make the chain saw
stops during operation because of getting too hot.
HIGH-TEMPERATURE INDICATOR (Fig. M)
The high-temperature indicator lights up when the
machine temperature exceeds 194°F (90°C) or the battery
temperature exceeds 158°F (70°C) during operation. The
temperature-protection circuit will immediately shut off
the machine to prevent overheating damage. Release the
trigger and wait until the overheated machine or battery
cools down and high-temperature indicator turns off, then
restart the machine.
BRAKE ICON (Fig. M)
The brake icon appears on the LCD screen when the
brake paddle is in brake position.
The brake icon will be flashing when the omni-directional
chain brake system stops the saw. See the next chapter
for detailed information.
OMNI-DIRECTIONAL CHAIN BRAKE SYSTEM (Fig.
N1 and Fig. N2)
The omni-directional chain brake system is not intended
to act as a substitute to the standard/traditional chain
brake. The user should never rely on this feature during
operation of the chain saw to protect against kickback.
Always follow safety instructions related to kickback
mitigation found in the warning section of this manual.
When the omni-directional chain brake system is activated
and stops the saw, the brake icon will be flashing on the LCD
screen (Fig. M). Release the trigger switch, remove the saw
chain and guide bar from the wood, then restart the chain
saw.
NOTE:
The sensors will only detect sudden motion of the
saw in the plane of the guide bar (fig. N1). The sensors
will not detect any sudden motion of the saw sideways
(fig. N2) (i.e., perpendicular to the plane of the guide bar).
OIL OUTPUT LEVEL AND LOW OIL INDICATOR
(Fig. M)
The machine automatically lubricates the chain. This chain
saw allows you to change the oil output rate with every press
of the oil-feeding button.
NOTE:
The oil output rate can only be changed when the
saw chain is not running.
The oil output level on the LCD screen will display the oil
output rate. One bar for low output rate, two bars for medium
output rate, and three bars for high output rate.
Choose a higher output rate for faster chain speed. If the saw
chain gets dry during work, stop the motor and choose a
higher oil output rate.
When the oil level is low, the low oil indicator above the oil
output bars will appear on the LCD screen and only low
output rate will be available. Stop the chain saw and refill
the oil tank following the chapter FILLING OIL TANK WITH
BAR AND CHAIN LUBRICANT.
After filling the oil tank, run the chain saw for about 10
seconds to allow the automatic lubrication system to start
working and the indicator will disappear from the LCD
screen.
NOTICE:
performing the above steps, the system may be damaged.
Stop using the chain saw and contact an EGO authorized
service center for repair.
LED HEADLIGHT (Fig. O)
The LED headlight is located in the front of the chain saw
housing. The headlight provides illumination for increased
visibility and features 2 brightness levels.
To turn on the headlight, press the headlight/Bluetooth
button (Fig. M) one time. The headlight will turn on in
low brightness level and the low brightness headlight
icon will appear on the LCD screen. Press the headlight/
Bluetooth button again to switch to high brightness level
and the high brightness headlight icon will appear on the
LCD screen.
To turn off the headlight, press the headlight/Bluetooth
button the third time and the headlight icon will disappear
from the LCD screen.
O-1
O-2
COMMUNICATION TECHNOLOGY
For information on our full range of connected products
and services, including connection instructions, please
scan QR Code below or visit www.egopowerplus.eu/
connect.
PROPER GRIP ON HANDLES (FIG. P1)
◾
Wear non-slip gloves for maximum grip and protection.
◾
With the saw on a firm, flat surface, hold the saw firmly
with both hands.
56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CSX5000
If the indicator is still on the LCD screen after
Low Brightness
O-3
Headlight Icon
High Brightness
Headlight Icon
EN
LED Headlight
11