Installation Checkout; Cleaning Instructions; Important Consumer Information - Kohler LOURE 98452T-CP Installation Instructions Manual

安装结果检查
检查并确保所有衔接处都已拧紧，打开排水系统
和主要供水源，检查并修理有漏水的接口。
清理说明
适用于所有加工处理过的表面，以中性肥皂水清
洗镀层表面，再以干净的软布彻底擦干整个表
面。许多清洁剂，比如氨水，去污粉及洁厕灵
等，会对电镀表面造成伤害，切忌使用。
有腐蚀性的清洁剂或溶剂不可使用于科勒的水龙
头及其配件上。
用户须知
1. 感应指示灯的各种闪烁情况
感应指示灯是使用者了解感应龙头有效、
唯一的途径。所以明白了感应指示灯闪烁
所代表的含义，可以正确使用感应龙头，
如图示:
(1) 快速闪烁，代表感应龙头正处于通电
后的30秒自动调节阶段。期间，安装者、
使用者不得干扰其自动调节，感应范围内
不要放置物体。
(2) 间隔约2秒钟连续闪烁:若直流感应龙
头, 代表龙头电池耗尽，已停止工作，等
待使用者更换电池;若交流感应龙头,表示
为两种情况：一种为刚刚停电；另一种为
在交流供电正常的情况下，则电源盒直流
接线端接触不良。
(3) 间隔6秒钟闪烁一次（直流版本），表
示电池即将使用完，请更换电池。
(4) 在正常工作情况下，当有物体被感应
时，龙头出水，感应指示灯闪烁一次。
（龙头关闭，感 应指示灯不闪烁。）
2.
超时出水控制
连续在感应状态下使用约一分钟，龙头自动止水。
自动止水后，手或物体离开感应范围后，再次进
入感应范围内，龙头正常工作，否则无反应。

INSTALLATION CHECKOUT

Check and ensure that all connections are tight. Open
the drain. Turn on main water supply and check for
leaks. Repair leakage when necessary.

CLEANING INSTRUCTIONS

Appliable for all finishes: clean the finish with a mild soap.
Wipe entire surface completely dry with a clean soft cloth.
Most cleaners may contain chemicals, such as ammonia,
chlorine, toilet cleaner etc. which could adversely affect the
finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets
and fittings.

IMPORTANT CONSUMER INFORMATION

指示灯
Indicator light
2. Timeout Setting
When the faucet works for about continuous 1 minute,
the faucet will stop flushing automatically. After that,
objects must be removed from the sensing range. Then
the water will flow when objects enter into the sensing
range again. Otherwise, the faucet will not work.
11
1. Note of the Indicator Flashing
The indicator is the only and effective way to
learn the faucet's working conditions. So the
users can use the sensor faucet correctly with
knowing the meaning of the sensor indicator's
flashing.
As shown:
(1) Quick flashing means the faucet is in the
period of adjusting sensing distance after power
on for 30s. During these 30s, please do not
disturb auto adjustment, no objects shall be put
in the sensing range.
(2) The indicator flashes every 2s: as for DC type
faucets, this indicates the unit out of battery and
ceases working. Please replace batteries. For
AC faucet, it indicates two possibilities: one is
that the unit is just out of battery; or poor DC
terminal contact under normal AC power supply.
(3) The indicator flashes every 6 seconds (DC
type) indicates that the unit is out of battery and
has stopped working. Replease batteries.
(4) Under normal condition, the water will flow
and the indicator will flash once when objects
are detected. (The indicator does not flash when
faucet stops flowing.)
1205259-2-F