Howmet Aerospace 2620 Instruction Manual
  1. Manuals
  2. Brands
  3. Howmet Aerospace Manuals
  4. Tools
  5. 2620
  6. Instruction manual

Howmet Aerospace 2620 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2620, A2620, 2620-PT,
A2620-PT
and
Hydraulic Installation Tools
Instruction Manual
Makers of Huck
, Marson
®
Brand Fasteners, Tools & Accessories
, Recoil
®
®

Table of Contents

2
4-5
5
6
7
8
9
10
11
11
12
13 - 14
14
15 - 18
17
19
19
21
May 15, 2023
HK1012

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2620 and is the answer not in the manual?

Questions and answers

Related Manuals for Howmet Aerospace 2620

Summary of Contents for Howmet Aerospace 2620

  • Page 1: Table Of Contents

    2620, A2620, 2620-PT, A2620-PT Hydraulic Installation Tools Instruction Manual Table of Contents EC Declaration of Conformity Safety Instructions Description Specifications Principle of Operation Preparation for Use Operating Instructions Maintenance Hydraulic Couplings Sticker Locations Tool Disassembly Procedure Tool Assembly Procedure 13 - 14...

  • Page 2: Ec Declaration Of Conformity

    1 Corporate Drive, Kingston, NY, 12401, USA Description of Machinery: Description of Machinery: Models 2600, 2620, 2624, 2630 family of hydraulic installation Models 2600, 2620, 2624, 2630 family of hydraulic installation tools and specials based on their design (e.g. PR####).
  • Page 3 2620 series Hydraulic Installation Tools (HK1012) DANGER - IMPORTANT DO NOT EXCEED HOSE MINIMUM BEND RADIUS Failure to heed the warnings below could lead to a damaged hose, damaged tool, damaged property, personal injury, or death. • This high pressure hose is not to be used other than assembled in a genuine HUCK tool or hose assembly or used as a replacement hose of a genuine HUCK tool or hose assembly.

  • Page 4: Safety Instructions

    2620 series Hydraulic Installation Tools (HK1012) Safety Instructions Remote triggers are available for hydraulic tooling if GLOSSARY OF TERMS AND SYMBOLS: pinch point is unavoidable. -Product complies with requirements set forth by 16. Do not abuse tool by dropping or using it as a hammer.

  • Page 5: Description

    Never-Seez is a registered trademark of Bostik, Inc. Description The 2620 series Hydraulic Installation Tools install a variety of HUCKBOLT® and Huck Blind Fasteners. These tools must be equipped with a nose assembly that is specifically designed for the installation of a specific fastener.

  • Page 6: Specifications

    2620 series Hydraulic Installation Tools (HK1012) Specifications Hose Kits: Use only genuine HUCK Hose Kits rated at 10,000 psi (689.5 bar) working pressure. Hydraulic fluid: Hydraulic fluid shall meet DEXRON III, DEXRON VI, MERCON, Allison C-4 or equivalent ATF specifications.

  • Page 7: Principle Of Operation

    2620 series Hydraulic Installation Tools (HK1012) Principle of Operation Figure 1a Figure 1b Piston Travel Piston Travel Pull Piston Pintail Ejector Dump Valve Trigger Switch Hydraulic Hoses Pressurized Oil Return Pressure Return Pressure Pull Pressure Pull Pressure Return Oil PULL PRESSURE...

  • Page 8: Preparation For Use

    2620 series Hydraulic Installation Tools (HK1012) Preparation for Use Read all WARNINGS and CAUTIONS before operating maintenance on HUCK equipment. WARNINGS: WARNING: Read full manual before Huck recommends that only using tool. A half-hour training session Huck Powerig Hydraulic Units be used as a with qualified personnel is recommended power source for Huck installation equipment.

  • Page 9: Operating Instructions

    2620 series Hydraulic Installation Tools (HK1012) Operating Instructions FOR SAFE OPERATION, THIS SECTION MUST BE READ AND UNDERSTOOD. Flange DOWN Bead UP Do NOT pull a fastener Do NOT install a fastener without a CORRECT CORRECT with the collar upside workpiece (structure to be fastened), a pin, down.

  • Page 10: Maintenance

    2620 series Hydraulic Installation Tools (HK1012) Maintenance STANDARD SEALANTS, LUBRICANTS CAUTIONS: Apply Parker Threadmate , Loctite 567, or Slic-Tite Consult Safety Data Sheet (SDS) ® ® ® male pipe threads per manufacturer’s instructions (to ease before servicing tool. Keep foreign matter out of the hydraulic assembly and to prevent leaks).

  • Page 11: Hydraulic Couplings

    Male Connector Sticker Locations The 2620 series tools are labeled with stickers that contain safety and pressure-settings information. These stickers must remain on the tool and be legible. Any sticker that becomes damaged or worn, or has been removed from the tool, or when replacing the cylinder, MUST be ordered and placed in the location shown below.

  • Page 12: Tool Disassembly Procedure

    NOTE: Complete step 5 only if the switch, wire, or connector is to be repaired. 5. Models 2620 & 2620-PT: Remove the retaining nut and locking ferrule from the strain relief. Loosen the setscrew and remove the switch. Loosen and remove the two wires from the switch.

  • Page 13: Tool Assembly Procedure

    7. Thread the GLYD Ring® Insertion Tool (P/N 121694- jaw vise and install the assembled Ejector Gland. Use 2620) into the back of the cylinder. (Figure 6) Hex Key (P/N 122048) to tighten. (Figures 4, 8, & 10) 8. Use a press to carefully push piston and front gland assembly into the back of the cylinder.

  • Page 14: Nose Assembly And Nose Disassembly

    16. Screw the coupling nipple (P/N 110438) onto the Models 2620 & 2620-PT: Slide the retaining nut and PULL pressure hose (from port P of tool). Screw the ferrule onto the electrical wire. Feed the wire through...

  • Page 15: Component Drawings

    2620 series Hydraulic Installation Tools (HK1012) Assembly Drawings Standard Models Figure 8 2620 & 2620-15 16 17 22 Ejector 22 EJECTOR Gland Asssembly GLAND ASSEMBLY Figure 9 A2620 16 17 22 Ejector 22 EJECTOR Gland Asssembly GLAND ASSEMBLY...
  • Page 16 2620 series Hydraulic Installation Tools (HK1012) Assembly Drawings PT Models Figure 10 2620-PT & 2620-PT-15 Figure 11 A2620-PT...

  • Page 17: Parts List

    2620 series Hydraulic Installation Tools (HK1012) Parts List The numerical references in the Item column are to the parts labels in Figures 8–11. 2620 & 2620-PT & ITEM DESCRIPTION QTY. A2620 A2620-PT 2620-15 2620-PT-15 Split Ring 102147 102147 102147 102147...
  • Page 18 2620 series Hydraulic Installation Tools (HK1012) Assembly Drawing Electric Trigger Figure 12 MODEL SELECTION MODELS(S) HOSE ASSEMBLY CONTROL CORD 2620, 2620PT 126107-1 123337-1 2620-15, 2620-PT-15 126107-2 123336 110439 Female Connector 110438 Male Connector 502298 Reducing Bushing (2) Hose Assembly (2)

  • Page 19: Troubleshooting

    2620 series Hydraulic Installation Tools (HK1012) Troubleshooting Always check the simplest possible cause (such as a loose or disconnected trigger line) of a malfunction first. Then proceed logically, eliminating other possible causes until the cause is discovered. Where possible, substitute known good parts for suspected defective parts.
  • Page 20 2620 series Hydraulic Installation Tools (HK1012) Notes...

  • Page 21: Warranties

    2620 series Hydraulic Installation Tools (HK1012) Limited Warranties Limited Lifetime Warranty on BobTail® Tools: Tooling, Part(s) and Other Items not manufactured by Huck: Huck International, Inc. warrants to the original purchaser that its BobTail® installation tools manufactured after HUCK makes no warranty with respect to the tooling, 12/1/2016 shall be free from defects in materials and part(s), or other items manufactured by third parties.
  • Page 22 Tel: +49-8251-8757-0 Fax: +33-1-34-33-97-77 HKSSalesDL@Howmet.com AICSalesDL@Howmet.com Huck provides technical assistance in the use 2023 Howmet Aerospace, Inc. © and application of Huck fasteners & tooling. NOTICE: This publication is only to be used for gen- Howmet Fastening Systems eral guidance in properties of the products shown...

This manual is also suitable for:

A26202620-ptA2620-pt

Table of Contents