Subscribe to Our Youtube Channel
Related Manuals for Howmet Aerospace 2057 Series
Summary of Contents for Howmet Aerospace 2057 Series
-
Page 1: Table Of Contents
2057 Series Pneudraulic Installation Tool Instruction Manual Table of Contents EC and UKCA Declarations of Conformity Safety Instructions Description Principle of Operation Specifications Preparation for Use Nose Assembly Installation and Removal Operating Instructions Maintenance Disassembly Procedure Assembly Procedure Sticker Location... -
Page 2: Ec And Ukca Declarations Of Conformity
2057 Pneudraulic Installation Tool (HK1227) EC Declaration of Conformity UKCA Declaration of Conformity Manufacturer: Manufacturer: Huck International, LLC, Industrial Products Group, Huck International, LLC, Industrial Products Group, 1 Corporate Drive, Kingston, NY, 12401, USA 1 Corporate Drive, Kingston, NY, 12401, USA Description of Machinery: Description of Machinery: Models 24#, 25#, 2047, and 2057 pneudraulic installation... -
Page 3: Safety Instructions
2057 Pneudraulic Installation Tool (HK1227) Safety Instructions I. GENERAL SAFETY RULES: 1. A half hour long hands-on training session with II. PROJECTILE HAZARDS: qualified personnel is recommended before using 1. Risk of whipping compressed air hose if tool is Howmet equipment. pneudraulic or pneumatic. -
Page 4: Description
2057 Pneudraulic Installation Tool (HK1227) Safety Instructions 5. Select, maintain and replace the consumable / inserted V. ACCESSORIES HAZARDS: tool as recommended to prevent an unnecessary 1. Disconnect tool from energy supply before changing increase in noise. inserted tool or accessory. 6. -
Page 5: Principle Of Operation
2057 Pneudraulic Installation Tool (HK1227) Principle of Operation Spring Hydraulic Piston Hydraulic Piston Spring Figure A Figure B Hydraulic Rod Hydraulic Rod Throttle Valve Diagram shows concept only Throttle Valve (RETURN position) and not an accurate depiction (PULL position) of the tool. Air Piston Air Piston Hydraulic Oil... -
Page 6: Preparation For Use
2057 Pneudraulic Installation Tool (HK1227) Preparation for Use WARNINGS: 1. Remove the plastic plug from air inlet connector and Only use recommended pin/ add a few drops of an approved hydraulic fluid. collar combinations with recommended pressure settings. Otherwise pulling a pin 2. -
Page 7: Operating Instructions
2057 Pneudraulic Installation Tool (HK1227) Operating Instructions Read all of these instructions in order to ensure the safe operation of this equipment. CAUTION: Remove excess gap from be- WARNINGS: Wear approved eye and hear- tween the sheets to permit proper fastener ing protection. -
Page 8: Disassembly Procedure
2057 Pneudraulic Installation Tool (HK1227) Disassembly Procedure This procedure is for complete disassembly of the 10. Remove the ball cable end from the throttle arm. tool. Disassemble only those components necessary to 11. Pull the cable from the handle. replace damaged O-rings, Back-up rings, and worn or 12. -
Page 9: Assembly Procedure
2057 Pneudraulic Installation Tool (HK1227) Assembly Procedure For components identification, see Components 5. Push piston rod through the piston from flat side, and Drawings on the following pages. screw the self-locking nut onto rod. Hold hex of rod with wrench, and torque nut to 28–32 ft.-Ibs. DO NOT scratch the piston rod or CAUTIONS: 6. -
Page 10: Component Drawings
2057 Pneudraulic Installation Tool (HK1227) Component Drawings 126082 131406 Front Gland Assembly 590517 Hydraulic Head Huck Trademark and 130300 130290 Assembly Year of Manufacture Sticker Pull Piston Cylinder Head 130286 Assembly 508526 End Cap ¼ NPT, 100309 Vented Bleed Plug Plug (available as 131406... - Page 11 2057 Pneudraulic Installation Tool (HK1227) Component Drawings 127326 - Gland Assembly 127324 502821 Gland Retaining Ring 500784 127327 O-Ring BU-Ring Patent sticker: 590543 500781 127328 131405 available in O-Ring BU-Ring Handle Asselmbly 127329 Polyseal 500779 O-Ring 500786 O-Ring 500101 127325 Screw Soc Cap Gland Housing 10-32 x .50...
-
Page 12: Fill And Bleed Procedure
2057 Pneudraulic Installation Tool (HK1227) Fill and Bleed This section documents the “bleed-&-fill” procedure. For returns to the idle position (full-forward). component identification, see Figures 1, 2, & 3. 0. Disconnect the tool from the air-line. REQUIRED EQUIPMENT 0. Lay the tool on its side and remove the fill bottle. Top Automatic Transmission Fluid (ATF) DEXRON III, off the fluid in the fill port, and install and tighten the •... -
Page 13: Troubleshooting
2057 Pneudraulic Installation Tool (HK1227) Troubleshooting Always check the simplest possible cause (such as a loose or disconnected trigger line) of a malfunction first. Then proceed logically, eliminating other possible causes until the cause is discovered. Where possible, substitute known good parts for suspected defective parts. -
Page 14: Warranties
2057 Pneudraulic Installation Tool (HK1227) Limited Warranties Limited Lifetime Warranty on BobTail® Tools: ooling, Part(s) and Other Items not manufactured by Huck: Huck International, Inc. warrants to the original purchaser that its BobTail® installation tools manufactured after HUCK makes no warranty with respect to the tooling, 12/1/2016 shall be free from defects in materials and part(s), or other items manufactured by third parties. - Page 15 Tel: +49-8251-8757-0 Fax: +33-1-34-33-97-77 HKSSalesDL@Howmet.com AICSalesDL@Howmet.com Huck provides technical assistance in the use 2023 Howmet Aerospace, Inc. © and application of Huck fasteners & tooling. NOTICE: This publication is only to be used for gen- Howmet Fastening Systems eral guidance in properties of the products shown...
Need help?
Do you have a question about the 2057 Series and is the answer not in the manual?
Questions and answers