Related Manuals for Handicare ARMREST SMART SEAT
Summary of Contents for Handicare ARMREST SMART SEAT
- Page 1 FREECURVE 1000 2000 4000 1100 ELEGANCE SMART SIMPLICITY SIMPLICITY STYLE ALLIANCE OUTDOOR STYLE STYLE CLASSIC SMART SMART SMART SEAT I N S T R U C T I O N INSTRUCCIÓN INSTRUCTIE ANLEITUNG INSTRUCTION ISTRUZIONE ARMREST CONVERSION...
- Page 2 ARMREST CONVERSION TOOLS REQUIRED 3 mm 1 ARM REST CONVERSION INSTRUCTION...
- Page 3 EXPLANATION Only a technician certified for this lift should service this lift (for more detailled information about the required competence see the installation manual). The latest instructions for the lift and instructions for options are available for download at www.handicarepartners.com. Turn off the lift.
- Page 4 ARMREST CONVERSION 3 ARM REST CONVERSION INSTRUCTION...
- Page 5 EXPLANATION [4]Carefully remove plastic bung from non-control arm by inserting small flat-head screw-driver. [5]Disconnect earth loom from pole-block. [6]Using small flat-head screwdriver, insert into the notch on stop switch pole block{A} and separate block from push-button{B}. [7]Remove screws(2x) which hold top and bottom mouldings together{A}. Remove the top moulding{B} [8]Disconnect stop switch pole block loom (pink, blue, grey).
-
Page 6: New Configuration
ARMREST CONVERSION 3 mm NEW CONFIGURATION NEW CONFIGURATION 5 ARM REST CONVERSION INSTRUCTION... - Page 7 EXPLANATION [9]Remove allen key screw which is currently securing earth wire{A}. Retighten the screw once the earth wire has been removed{B}. [10]Remove earth wire and pole block from non-control arm. [11]Refit the leaf spring. [12]Secure using top-hat nut, the toggle and arm lever switch fastener inside new control arm. [9]Verwijder de inbusschroef die de aardedraad vastzet{A}.
- Page 8 ARMREST CONVERSION NEW CONFIGURATION ONLY POWERED FOOTREST NEW CONFIGURATION 7 ARM REST CONVERSION INSTRUCTION...
- Page 9 EXPLANATION [13]Insert the toggle switch{A} and make the loom connection{B}. [14]Remove the dop from the top moulding of the old control arm. [15]Only powered footrest: remove the cap and install the powered footrest switch{B} [16]Remove stop switch from top moulding by undoing plastic washer/nut{A}. Press-in plastic component into new control arm{B}.
- Page 10 ARMREST CONVERSION NEW CONFIGURATION NEW CONFIGURATION NEW CONFIGURATION 3 mm NEW CONFIGURATION NEW CONFIGURATION 9 ARM REST CONVERSION INSTRUCTION...
- Page 11 EXPLANATION [18]Feed pole block loom through bottom moulding{A}. Make the stop switch loom connection{B}. [19]Feed ground wire through insert in bottom moulding. [20]Loosen allen key screw{A}. Feed ground wire through new non-control arm pivot{B} and secure with allen key screw{C}. [21]Place stop switch into new non-control arm, ensure ‘STOP’...
- Page 12 ARMREST CONVERSION NEW CONFIGURATION NEW CONFIGURATION CHECK FUNCTIONS REPLACED PARTS NEW CONFIGURATION CONTINUE WITH A NORMAL INSTALLATION 11 ARM REST CONVERSION INSTRUCTION...
- Page 13 EXPLANATION [23]Connect pole block to E-Stop. [24]Connect the blue wire to the pole block{A} and connect the earth wire to the pole block{B}. [25]Place plastic bung, to cover pole block. Ensure bung is in correct orientation. Continue wiyhe a normal lift installation [26]After installation check the function of the replaced parts.
- Page 16 Canada Deutschland T : 905.850.9003 Tel: +49 (0) 571 973398-55 Fax: +49 (0) 571 973398-56 F : 416.260.0256 data@handicare.com Handicare Montascale Italia Via Chiaviche 17 46020 Pegognaga (MN) Italy Tel: +39 (0) 376 143 3516 handicare-montascale.it SM ARMREST CON INSTRUCTION...