Related Manuals for Ice SWEEP 50 B-P
Summary of Contents for Ice SWEEP 50 B-P
- Page 1 SWEEP 50 B-P SWEEPING MACHINES USE AND MAINTENANCE MANUAL ORIGINAL INSTRUCTION DOC. 10068706 - Ver. AA - 02-2017...
- Page 2 The descriptions contained in this document are not binding. The company therefore reserves the right to make any modifications at any time to elements, details, or accessory supply, as considered necessary for reasons of improvement or manufacturing/commercial requirements. The reproduction, even partial, of the text and drawings contained in this document is prohibited by law.
-
Page 3: Table Of Contents
CONTENTS ON CONSIGNMENT OF THE MACHINE ..............................4 SERIAL NUMBER PLATE ..................................4 INTRODUCTION ....................................4 IDENTIFICATION DATA ..................................4 TECHNICAL DESCRIPTION .................................. 4 INTENDED USE ....................................4 SYMBOLS USED ON THE MACHINE ..............................6 GENERAL SAFETY REGULATIONS ............................... -
Page 4: On Consignment Of The Machine
On consignment of the machine Serial number plate When the machine is consigned to the customer, an immediate check to ensure that all the material mentioned in the shipping documents has been received, that the machine has not suffered damage during transportation should be performed. - Page 5 TECHNICAL DESCRIPTION SWEEP 50P SWEEP 50B Working width without side brush Work capacity, up to 2275 2275 Maximum gradient Central brush dimensions 500x265 500x265 Debris hopper capacity Honda internal combustion engine Electric motor Electric motor Filtering surface Type of advance Forward speed km/h 0÷3.5...
-
Page 6: Symbols Used On The Machine
SYMBOLS USED ON THE MACHINE Filter shaker Suction switch-off Side brush Wear hearing protection Pay attention to hot parts On/off (battery-operated versions only) ON / 1 Battery charge signal (battery-operated versions only) Indicates the maximum gradient... -
Page 7: General Safety Regulations
When anomalies in the functioning of the machine are found, adjustment or repair must only be performed by qualified and trained personnel. Otherwise, especially for anomalies involving electrical parts, request the intervention of the ICE technical assistance centre. When replacing parts, request original spare parts from our dealer or our assistance service. - Page 8 The batteries must be disposed of in a safe manner, fully observing the laws and regulations in force. Disconnect the battery before cleaning or maintenance.
-
Page 9: Machine Preparation
MACHINE PREPARATION 1. HANDLING THE PACKAGED MACHINE The machine is contained within specific packaging. It is not possible to place more than two packages on top of each other. The overall dimensions of the package are: SWEEP 50 153 cm 76 cm 119 cm Weight of packed SWEEP 50B machine:... -
Page 10: Battery Fitting (Sweep 50B Version)
MACHINE PREPARATION 5. BATTERY FITTING (SWEEP 50B VERSION) The machine can be supplied with batteries included. If using a battery other than those supplied with the machine, check that the size is suitable for the battery compartment Perform a battery charging cycle before using the machine. The batteries must be housed in the appropriate compartment beneath the recovery tank, and must satisfy the requisites of Standard CEI 21-5. -
Page 11: Battery Indicator (Sweep 50B Version)
MACHINE PREPARATION To connect the battery charger you must: 1. Make sure the main switch is in the “0” position 2. Move the machine near to the battery charger 3. Open the hood of the machine 4. Disconnect the battery connector (2) from the electric system (1). 5. -
Page 12: Instrument Panel Components(Sweep 50P Version)
MACHINE PREPARATION 11. INSTRUMENT PANEL COMPONENTS(SWEEP 50P VERSION) The instrument panel components are identified as follows: 1. Suction tube closure (a): determines the closure of the fan's suction duct through the movement of a hatch, which on contact with the stop activates the electric filter shaker. 2. -
Page 13: Work
WORK 1. PREPARING TO WORK (SWEEP 50B VERSION) 1. Check that the main switch of the machine is set to "0" 2. Open the hood of the machine 3. Connect the battery connector (2) to the electric system connector (1) 4. -
Page 14: Side Brush
WORK For suction efficiency, clean the filter approx. every 10 min. Proceed as follows: close the suction (lever a); activate the manual filter shaker repeatedly (lever b); for the version with electric filter shaker, pull the lever (a) for a few seconds at the end of run ... -
Page 15: At The End Of The Work
AT THE END OF THE WORK 1. AT THE END OF THE WORK At the end of the work, and before carrying out any type of maintenance: 1. Bring the machine to the place provided for debris discharge 2. Position the machine's main switch (d) to “0” (for SWEEP 50B versions) 3. -
Page 16: Daily Maintenance
DAILY MAINTENANCE PERFORM ALL MAINTENANCE OPERATIONS IN SEQUENCE 1. FILTER CLEANING (VERSION WITH FIXING TAB) Proceed as follows to clean the suction filter: 1. switch off the machine 2. Remove the debris hopper 3. Lift the filter shaker (a) and lock it in the raised position with the special pin supplied with the machine. -
Page 17: Filter Cleaning (Version With Fixing Bracket And Electric Filter Shaker)
DAILY MAINTENANCE 3. FILTER CLEANING (VERSION WITH FIXING BRACKET AND ELECTRIC FILTER SHAKER) Proceed as follows to clean the suction filter: 1. switch off the machine 2. Remove the debris hopper 3. Disconnect the red connector of the filter shaker motor 4. -
Page 18: Weekly Maintenance
WEEKLY MAINTENANCE 1. SIDE BRUSH ADJUSTMENT The brush height adjustment is made by means of screw (a) inside the support bracket (b) of the brush. The brush must be compressed against the ground for about 2 cm. 2. CENTRAL BRUSH ADJUSTMENT The central brush should operate flattened to the ground by 7/8 mm. -
Page 19: Troubleshooting
ICE service centre. 2. The debris hopper is full: empty it. 3. The brush does not turn because the belt is broken: have it replaced by ICE assistance centre. 2. THE MACHINE RAISES DUST WHILE CLEANING 1. The flaps that ensure efficient suction are worn: replace them. -
Page 20: Demolition Of The Machine
DEMOLITION OF THE MACHINE To dispose of the machine, take it to a demolition centre or an authorised collection centre. Before scrapping the machine, it is necessary to remove and separate the following materials and then send them to the appropriate collection centres, in accordance with the currently effective environmental hygiene regulations: brushes ... -
Page 21: Choosing The Brushes
CHOOSING THE BRUSHES TABLE FOR CHOOSING THE BRUSHES Machine No. of brushes Code Type of bristles Brush Notes Brush Bristle length 411679 411683 PPL + STEEL 0.7 + 0.5 Central brush 411682 TAMPICO SWEEP 50B SWEEP 50P 414295 PPL + COPPER 0.6 + // 411690 Side brush... - Page 22 37059 - S. Maria di Zevio (VR) - Verona - Italia Chapel Lane, Totton, Hampshire, SO40 9AH Tel. +39 045 6060411 - Fax. +39 045 6060417 Tel. 0800 389 3869 - Fax. 023 8042 8318 E-mail: service@fimap.it E-mail: info@ice-clean.com Web: www.fimap.com Web: www.ice-clean.com...
- Page 24 Industrial Cleaning Equipment Ltd. Sauber House, Unit 3, Rushington Business Park - Chapel Lane, Totton, Hampshire, SO40 9AH Service 0800 389 3869 - Facsmile 023 8042 8318 - Email info@ice-clean.com...