Related Manuals for Ice i20B
Summary of Contents for Ice i20B
- Page 1 OPERATOR & Parts Manual www.icecompanies.com i20B 8038002 REV.03(03-2015) INTERNATIONAL CLEANING EQUIPMENT...
- Page 2 Customer ID Number Installation Date HOW TO ORDER PARTS Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered online,by phone, by fax or by mail. 1. Identify the machine model. 2. Identify the machine serial number from the data label.
-
Page 3: Table Of Contents
WEAR & TEAR PARTS LIST....28 WIRING DIAGRAM ......29 ICE i20B... -
Page 4: Safety Precautions
Do not pick them up. – Stop on level surface. – Turn off machine. 5. When servicing machine: – Read operator's manual thoroughly prior to operating or servicing this machine. – Use manufacturer supplied or approved ICE i20B... -
Page 5: Machine Components
26. Squeegee Lifing Level - Flow Decrease Switch 14. Filter Assembly 27. Recovery Tank 4. Brush Motor Indicating 15. 8 Inch Wheels 28. ICE Logo Light 16. 3 Inch Castors 29. Solution Tank 5. Vacuum Motor Switch & 17. Batteries 30. -
Page 6: Machine Setup & Installation
RED to POSITIVE, BLACK to NEGATIVE securing knobs. 3. Connect the vacuum hose to the squeegee assembly. Loop the hose by using the hose clip provided. 4. Check the squeegee blades for proper adjustment. ICE i20B... -
Page 7: Machine Operation
5. Check the soluion flow indicator (see machine components, item #3), adjust the solution flow control switch to a desired flow rate. NOTE: Solution will not begin to flow until the control handle is pulled. ICE i20B... -
Page 8: Tank Draining
#18) upward, remove the cap and lower hose to drain. 2. Open the cover tank and rinse out the tank. Use a rag to remove any excess dirt. 3. Clean the float shut-off screen located in the recovery tank. ICE i20B... -
Page 9: Preventative Maintenance
8. Upon completion of charging, disconnect the AC power supply cord first, and then MOTOR MAINTENANCE disconncet the charger from the machine. 1. Contact your local ICE Distributor for any motor maintenance. PREVENTIVE MAINTENANCE 2. Check the motor brushes every 250 hours, Replace the brushes when they are worn to a length of 10mm or less. - Page 10 Any damage caused by freezing temperatures will not be covered by the warranty. 7. Drain the recovery tank and keep the cover tank open so that it can "breathe" during storage. 8. Drain the solution tank of all fluid. ICE i20B...
-
Page 11: Basic Troubleshooting
Malfunctioning controller Contact ICE Distributor Faulty key switch Contact ICE Distributor Battery meter lockout activated Recharge batteries Faulty control handle bail switch Contact ICE Distributor Brush motor Faulty brush motor or wiring Contact ICE Distributor will not run Worn motor carbon brushes... -
Page 12: Technical Specification
0-1.4 bush motor voltage and power V / W 24 / 550 vacuum motor voltage and power V / W 24 / 500 batteries Ah @ 20hr working vacuum mbar Max Gradient Noise level ICE i20B... -
Page 13: Parts List
PARTS LIST SOLUTION TANK ASSEMBLY ICE i20B... - Page 14 HOSE CLAMP 16-25mm 8031006 SOLUTION DISPLAYER 8131020 RECOVERY TANK STAY CORD 1421612 PLAIN WASHER 6×12×1.6 SS 1021616 HEX HEAD BOLT M6×16 8133002 PLUG 1113305 SELF-LOCKING NUT M3 8113010 BRACKET 1422513 SPRING WASHER 5 SS 8113017 CONNECTING CABLE BLACK ICE i20B...
- Page 15 DESCRIPTION NUMBER REQ'D 8113018 CONNECTING CABLE RED 1211325 PH SCREW M3×25 1434300 TOOTHED LOCK WASHER M3 8113021 CONNECTOR HANDLE 8113020 CONNECTOR 8113009 CABLE CLIP 8113007 RUBBER STRIP 1321213 PH AUTO-TAPPING SCREW ST4.2×13 8113002 COVER 8113030 SEAL 8031004 DECAL ICE i20B...
- Page 16 PARTS LIST RECOVERY TANK ASSEMBLY ICE i20B...
- Page 17 PAN HEAD SCREW M4×10 8111001 SEALING GASKET 8111014 FILTER COUPLING 1421618 PLAIN WASHER 6×18×1.6 SS 1021616 HEX HEAD BOLT M6×16 SS 8111015 FLOAT CAGE 8032004 DECAL 8011009 PLATE 8111022 WARNING DECAL 8033001 COVER TANK 8033002 SEALING STRIP 8011005 ICE i20B...
- Page 18 PARTS LIST CONTROL BOX ASSEMBLY ICE i20B...
- Page 19 SELF-LOCKING NUT M6 SS 1421518 PLAIN WASHER 5×18×2 SS 1021512 HEX HEAD BOLT M5×12 8014012 BAFFLE 1021630 HEX HEAD BOLT M6×30 SS 8014101 SPACER 8014038 SEALING GASKET 8034006 DECAL 8114709 KEY SWITCH 1221410 PAN HEAD SCREW M4×10 SS 8034004 PANEL DECAL ICE i20B...
- Page 20 PAN HEAD SCREW M3×6 SS 8114101 SHAFT 1221412 PAN HEAD SCREW M4×12 SS 1422411 SPRING WASHER 4 SS 1411409 PLAIN WASHER 4×9×0.8 8014033 PLATE 1534608 SET SCREW M6×8 8014031 HEX BUSHING 8014032 SPRING ROD 8014035 SPRING 8014022 CONTROL HANDLE ICE i20B...
- Page 21 PARTS LIST i20B BRUSH ASSEMBLY ICE i20B...
- Page 22 PARTS LIST i20B BRUSH ASSEMBLY PART DESCRIPTION NUMBER REQ'D 8116005 BRUSH MOTOR, 24VDC 1.0HP 1656432 KEY 1221412 SCREW M4×12 1422513 LOCK WASHER M5 1421518 FLAT WASHER M5× ∮ 18×2 8116100 WATER SUPPLY TUBE 8116006 SCRUB HEAD HOUSING 8116020 BUMPER, SCRUB HEAD...
- Page 23 PARTS LIST CHASSIS ASSEMBLY ICE i20B...
- Page 24 8031002 3" CASTOR 8036010 CHASSIS 1123608 SELF-LOCKING NUT M6 SS 1021825 HEX HEAD BOLT M8×25 SS 8036006 BRUSH GUIDING BRACKET 1421612 PLAIN WASHER 6×12×1.6 SS 1422616 SPRING WASHER 6 SS 1021616 HEX HEAD BOLT M6×16 SS 8117009 SPRING ICE i20B...
- Page 25 PARTS LIST SQUEEGEE HOLDER ASSEMBLY PART DESCRIPTION NUMBER REQ'D SPRING 8115004 HEX HEAD BOLT M12×30 1021230 BUSHING 8115405 PLAIN WASHER 13×32×1.5 1421132 SQUEEGEE BRACKET 8037002 SQUEEGEE SUPPORT 8115001 SELF-LOCKING NUT M12 1123115 8115003 COTTER PIN 3.2×24 1645324 ICE i20B...
- Page 26 PARTS LIST SQUEEGEE ASSEMBLY ICE i20B...
- Page 27 SELFLOCKING NUT M5 1221570 PH SCREW M5×70 8118610 CLAMP ASSEMBLY 8118022 REAR SQUEEGEE LINATEX 8118002 REAR SQUEEGEE PU(OPTIONAL) 8118021 FRONT SQUEEGEELINATEX 8118001 FRONT SQUEEGEE PU (OPTIONAL) 8118005 SQUEEGEE HOLDER 8118200 BRACKET,LEFT 1421816 PLAIN WASHER 8×16×1.6,SS 1123810 SELFLOCKING NUT M8 ICE i20B...
-
Page 28: Wear & Tear Parts List
WEAR & TEAR PARTS WEAR & TEAR PARTS LIST PART DESCRIPTION NO NUMBER REQ'D 8115200 8" WHEEL 1612604 6004RS BEARING 8116009 BUMPER WHEEL 8118021 FRONT SQUEEGEELINATEX 8118022 REAR SQUEEGEE LINATEX 9050020 20" BRUSH(FOR i20B) 9040019 19" PAD DRIVER(FOR i20B) ICE i20B... -
Page 29: Wiring Diagram
CONTROL HANDLE SWITCH SW1: BRUSH MOTOR SWITCH SW2: KEY SWITCH CTRL: SCRUBBER CONTROLLER PCB: ELECTRONIC BOARD LED: LED INDICATOR LIGHT SOLUTION SOLENOID VALVE BRUSH MOTOR VACUUM MOTOR BLK: BLACK BLU: BLUE BRN: BROWN GRN: GREEN RED: WHT: WHITE YEW: YELLOW ICE i20B...