Vela Tango 700 Instructions For Use Manual
Hide thumbs
Also See for Tango 700:
- Mounting instructions (2 pages) ,
- Instructions for use manual (16 pages) ,
- Mounting instructions (2 pages)
Related Manuals for Vela Tango 700
Summary of Contents for Vela Tango 700
- Page 1 I N S T R U C T I O N F O R U S E VELA Tango 700 & 700E VERSION: Manual no. 105675 VELA Tango 700 VELA Tango 700E ISO 9001 ISO 14001...
- Page 2 CHAIR FUNCTIONS Backrest height Backrest angle Electric height adjustment Seat depth Manual height adjustment Brake Seat angle Tilt Seat rotation Armrest height Armrest width (handle on left side) Lenght:...
- Page 3 GETTING STARTED Brake the chair and sit back in the seat. There should be about 3 cm between the seat cushion and the back of your knees. Adjust the seat angle and height so that you sit comfortably with your feet flat on the floor. Adjust the backrest height and angle to adjust the seat depth and support your lower back and back.
-
Page 4: Table Of Contents
TABLE OF CONTENTS 1.0. INTRODUCTION 1.1. WARNINGS 1.2. TROUBLESHOOTING 1.3. VELA TANGO WITH ELECTRIC HEIGHT ADJUSTMENT 1.3.1. Power input 1.3.2. Emission 1.3.3. Surge protection 1.4. LABELS USED ON THE CHAIR 1.5. SAFETY 1.5.1. Intended use 1.5.2. Transport 1.6. WARRANTY 1.7. UNPACKING THE CHAIR 1.8. -
Page 5: Introduction
1.0. INTRODUCTION DEAR CUSTOMER Congratulations on your new VELA chair! We are sure this chair will give you daily pleasure. This user manual provides useful information on adjusting, operating and maintaining your chair. Important Please read this user manual carefully and keep it safe for when you need to refer to it. -
Page 6: Warnings
1.1. WARNINGS In case of an allergic reaction, stop using the chair and consult a doctor Only use original spare parts from VELA Only use the supplied charger for charging the chair Do not make any changes to the accessories that come with the chair... -
Page 7: Troubleshooting
See section 2.0.15 Brake rod seems loose The hand screw holding the brake rod might be loose. Tighten the screw. See section 2.0.18. If the above does not solve your problem, you should contact your VELA supplier. -
Page 8: Vela Tango With Electric Height Adjustment
Current: 0.5A Power: 12VA 1.3.2. EMISSION A VELA chair with electrical functions has been tested and complies with current requirements regarding electromagnetic radiation (EMC requirements). The chair is tested to the following specifications: :: Emission class CISPR 11, Group 1, Class B See more details at www.vela.eu... -
Page 9: Labels Used On The Chair
9200 Aalborg SV, Denmark. :: The chair is not built to stand on The VELA Tango with electrical func- tions meets all safety requirements :: The wheel brake must always be according to IEC 60601-1, including... -
Page 10: Transport
:: VELA chair :: Instructions for use 1.6. WARRANTY :: Charger (only for chairs with elec- VELA grants a right of claim under trical functions) applicable law in the country where the chair is acquired. The right of Note: see item 2.0.1 for correct complaint applies only when using attachment of backrest. -
Page 11: Wheels
1.8.4. RECYCLING GUIDE Your VELA chair can be reused by another person when you no longer need it as long as the chair is ser- It is important that you return your viced by a technician beforehand. -
Page 12: Settings
2.0. SETTINGS The gas spring and the electric lifting mechanism should only be replaced by a VELA technician or a person trained in this field. STD. BACK 2.0.1. ATTACHING THE BACKREST The backrest is lowered into the hole. Screw the handle back on and tighten securely. -
Page 13: Height Adjustment (Manual)
Note: Setting the angle of backrest and seat should always be done with your feet flat on the floor. VELA TANGO 2.0.4. HEIGHT ADJUSTMENT (MANUAL) Adjusted by pulling up the front handle on the right-hand side. 2.0.5. SETTING ANGLE OF SEAT Adjusted by pulling up the middle handle on the right-hand side. -
Page 14: Adjustment Of Seat Depth
2.0.8. ADJUSTMENT OF SEAT DEPTH Adjusted by pulling up the rear handle on the right side (backrest angle). Adjusted so that the seat depth suits the user of the chair. Operate the handle only when someone is sitting in the chair, as the backrest tilts forward. -
Page 15: Adjusting The Armrest Height
2.0.12. ADJUSTING THE ARMREST HEIGHT Adjusted by loosening the screw on the armrest bar and adjusting the height of the armrest. Remember to tighten the screw when done. 2.0.13. ADJUSTING THE ARMREST WIDTH Adjusted by loosening the screw under the seat on the seat support and adjusting the armrest width by pulling out the armrest. -
Page 16: Brake
2.0.16. BRAKE The brake is activated by moving the handle on the side of the chair forward. Unlock the chair by moving the handle back into the upright position. Note: See Setting the angle of the brake, section 2.0.18. for adjusting the position of the brake and the distance to the seat. -
Page 17: Charging (El)
TANGO The hand box is used via push buttons on the front. VELA hand boxes can have one or more functions. The icons on the hand box show the button functions. Note: Insert plug in hand box to operate functions. -
Page 18: Folding Footrest
2.0.24. FOLDING FOOTREST* Stabilising foot support that can also be used as a footboard when moving in and out of the chair. 2.0.25. SIDE-MOUNTED SWIVEL FOOTREST* Mounted on the underside of the front right and/or left chair legs. the footrest can be turned in/out and provide support for a leg as needed. -
Page 19: Accessories
2.0.28. ACCESSORIES This chair is available with a wide range of accessories. See a complete list of accessories at: www.vela.eu Note: Charger is included as an accessory when purchasing a VELA chair with electrical functions. Depending on model... - Page 20 VELA :: Gøteborgvej 8-12 :: 9200 Aalborg SV :: Denmark :: Tel: +45 96 34 76 00 :: mail@vela.dk...