This User Manual does not address the end user� It is intended as a source of information for the equipment or system manufacturer only, and it will tell you how to install, use and maintain your LINAK electronics� The manufacturer of the end product has the responsibility to provide a User Manual, where relevant safety information from this manual is passed on to the end user�...
Failure to comply with instructions marked with the ”NOTICE” symbol may result in serious damage to the system or one of its components� Read all instructions before using this product� Important safety information on LINAK products can be found under the following heading(s): ®...
DF2 | Important safety instructions General DANGER Plugged-in products Risk of electric shock • Always unplug this product from the electrical outlet before assembling, disassembling, cleaning, or servicing� • Only use the product indoors in dry locations� WARNING General precautions Risk of burns, fire, electric shock, or injury to persons •...
DF2 | Intended use This product is intended for use indoors in household and commercial usage areas� Do not use outdoors or in wet areas� Before installation, re-installation, cleaning, or troubleshooting • Stop the system� • Unplug the mains cable� •...
® In order to avoid the risk of malfunction, all DESKLINE repairs must only be carried out by authorised LINAK ® workshops or repairers, as special tools must be used and special gaskets must be fitted� Lifting units under...
Le non-respect des instructions marquées du symbole “AVIS” peut entraîner de graves dommages au système ou à l’un de ses composants� Lisez toutes les instructions avant d’utiliser ce produit� Des informations de sécurité importantes sur les produits LINAK sont disponibles dans la ou les rubriques ®...
DF2 | Consignes importantes de sécurité Général DANGER Produits enfichés Risque de choc electrique • Débranchez toujours ce produit de la prise électrique avant de l’assembler, de le démonter, de le nettoyer ou de l’entretenir� • N’utilisez le produit qu’à l’intérieur, dans des endroits secs� AVERTISSEMENT Précautions générales Risque de brûlures, d’incendie, d’électrocution ou de blessure des personnes...
DF2 | 10 Utilisation prévue Ce produit est destiné à être utilisé à l’intérieur des habitations et des locaux commerciaux� Ne pas utiliser à l’extérieur ou dans des zones humides� Avant l’installation, la réinstallation, le nettoyage ou le dépannage • Arrêter le système� •...
être effectuées ® par des ateliers ou des réparateurs LINAK agréés, car des outils spéciaux doivent être utilisés et des joints spéciaux doivent être montés� Les unités de levage sous garantie doivent également être retournées aux ateliers LINAK agréés�...
EU DECLARATION OF CONFORMITY EU Declaration of Conformity LINAK A/S Smedevænget 8 DK - 6430 Nordborg Herewith declares under our sole responsibility that LINAK DESKLINE ® products as characterized by the following models and types: DF2 Beam models: DF2B000a00b00000A009 (a=0 or 1; b=A,B,D or X where X equals any colour) DF3 Beam models: DF3B000a0bcd000fgh09 (a=0,1,2;...
Page 13
DF2 | 13 complies with EMC Directive: 2014/30/EU (OJ L 96, 29.3.2014, p. 79–106) according to following standards: EN 61000-6-1:2007, EN 61000-6-3:2007+A1:2011+AC:2012 complies with Low Voltage Directive 2014/35/EU (OJ L 96, 29.3.2014, p. 357–374) according to the standard: EN 60335-1:2012+AC:2014+A11:2014 +A13:2017+A1:2019+A14:2019+A2:2019+A15:2021 Complies with Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (OJ L 174, 1.7.2011, p.
DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY LINAK A/S Smedevænget 8 DK - 6430 Nordborg Herewith declares that LINAK DESKLINE ® products as characterized by the following models and types: DF2 Beam models: DF2B000a00b00000A009 (a=0 or 1; b=A,B,D or X where X equals any colour) DF3 Beam models: DF3B000a0bcd000fgh09 (a=0,1,2;...
Page 15
DF2 | 15 comply with the following parts of the Machinery Directive 2006/42/EC, ANNEX I, Essential health and safety requirements relating to the design and construction of machinery: 1.1.2 a) Fitted for function and foreseeable misuse* 1.1.2 b) Selection of the most appropriate methods* 1.1.2 c) Foreseeable misuse* 1.2.1 Safety and reliability of control systems 1.2.2 Control devices.
If you disconnect mains, the DF2 SW cannot work and thus not calculate the temperature� When the system is powered on again, the SW will continue to calculate using the data from when the mains was disconnected� Warranty The warranty terms for DESKLINE products are described in this warranty paper: https://cdn�linak�com/-/media/files/warranty/warranty-paper-deskline-eng�pdf...
DF2 | 17 Maintenance Clean dust and dirt from the outside of the system at appropriate intervals and inspect for damage and breaks� Inspect connections, cables, and plugs without disconnecting, and check functioning as well as fixing points� CAUTION Loose screws Risk of loss of stability •...
Page 18
1180 mm - 1829 mm (46.5" - 72") Modified By Jan Kring 2023-02-28 Customer No.: DF22-tabletop-size-T-desk Created By Bjarne Skov 2023-02-21 LINAK Drawing No.: 1066W4037 Drawing No� 1066W4038 Figure 3 DF2 (C-desk design) with cantilevers mounted centrally on the tabletop...
DF2 | 19 Installation A mounting instruction video is available here� NOTICE Delivery • Check the packaging and the delivered items for visible damaged� If there is visible damage to the product, do not install it� WARNING Plastic bags Risk of suffocation •...
Page 20
DF2 | 20 CAUTION Sharp edges on tabletops Risk of injury to persons� • Use tabletops with rounded edges which comply with EN527� CAUTION Tilting table Risk of injury to persons • Do not mount the frame on tabletops bigger than the recommended size� •...
DF2 | 21 Preparing the assembly 1� Gather all parts for the desk including the tabletop� 2� Turn the tabletop upside down� Assembling the top frame 1� Adjust the beam length� Be careful when adjusting the beams� Fingers may get squeezed� 1�1�...
DF2 | 22 Mounting the cantilevers 1� Place a cantilever slightly tilted at the end of the beam� 2� Press the cantilever into place until a click is heard and the snap joint locks the cantilever in the correct position� 3�...
DF2 | 23 Mounting the columns 1� Ensure that the columns are completely retracted� If the column extracts when turned upside down, press by hand to completely retracted position� Be careful when mounting the columns� Fingers may get squeezed or crushed� 2�...
DF2 | 24 Mounting the desk panel Ensure that only one desk panel at the time is connected to the DF2� 1� Connect the desk panel in one of the RJ45 sockets� 2� Mount the DPF using a 90° mounting bracket (article number 914759) and place it close to the tabletop edge�...
DF2 | 25 Mounting the feet On-top or recessed In case of a C-desk design, ensure to turn the feet in the correct direction to avoid tilting of the desk� 1� Mount the feet on the columns using four M6 or two M8 mounting screws for each foot� The columns have four M6 and two M8 threaded holes in the bottom plate�...
Page 26
DF2 | 26 Click-on A mounting instruction video is available here� The Click-on Feet can only be used with columns with pre-mounted mounting screws and plastic plate� 1� Align the holes in the foot with the screws on the column� 2�...
DF2 | 27 3� Ensure that locking plates snap inwards and lock the screws� Finalising the installation 1� Flip the desk over� It is recommended not to flip the desk over single-handed as the desk is too heavy� You might get injured, or the desk might be damaged if dropped�...
Page 28
DF2 | 28 Disassembling the DF2 1� Drive the desk to its minimum height so the columns are completely retracted� 2� Disconnect from the mains supply� 3� Flip the desk over� It is recommended not to flip the desk over single-handed as the desk is too heavy� You might get injured, or the desk might be damaged if dropped�...
CAUTION Heavy load Risk of injury to persons • Place heavy load centrally on the desk For operation of the desk, please see the relevant desk panel User Manual which is available on: https://www�linak�com/user-manuals/deskline/ Troubleshooting/FAQs Error codes Error code Description...
LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question�...
DF2 | 31 Disposal of LINAK products As LINAK customers often ask us how our products can be disposed or scrapped, we have prepared this guide that enables a classification to different waste fractions for recycling or combustion� Guide We recommend our products to be disassembled as much as possible and divided into different waste groups for recycling or combustion�...
LINAK, LINAK subsidiaries, or LINAK affiliates. the same reason, LINAK cannot guarantee the correctness and actual status of imprinted information on All sales are subject to the ‘Standard Terms of Sale and Delivery for LINAK A/S’ available on LINAK websites. its products.
Need help?
Do you have a question about the DESKLINE Desk Frame 2 and is the answer not in the manual?
Questions and answers