Wali GMF002 Installation Manual

INSTALLATION MANUAL
Dual Monitor Desk Stand
GMF002

Supplied Parts List

Swivel Arm Pole
A (x1) B (x1)
M5x16 Bolt M10 Bolt M6 Nut
I (x4) J (x1) K (x2)
1

Option B : Grommet Base Installation (Existing Grommet Hole Installation)

If the existing grommet hole comes with a plastic protector, remove it to ensure a flat
surface before installing the desk mount. Position the Pole B and Anti-skid Pad G on
the mounting surface and secure using the Support Plate H , D10 Washer O , D10
Washer N , and M10 Bolt J . Fasten the Bolt using the provided Wrench R . N J
B
G
H
O
N
J
R
Base VESA Plate
C (x1) D (x2) E (x4)
Wire Clip Wire Clip D10 Washer D10 Washer
L (x4) M (x1) N (x1) O (x1)
1

Option B : Grommet Base Installation (Self-drilled Grommet Hole Installation)

Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm) diameter hole
B G
at the marked position through the mounting surface. Position the Pole B and Anti-skid
H O Pad G on the mounting surface and secure using the Support Plate H , D10 Washer O , G
R D10 Washer N , and M10 Bolt J . Fasten the Bolt using the provided Wrench R .
R

WARNING

！
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.

TIPOVER WARNING

！
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
www.walielectric.com
● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
support@walielectric.com
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
1-844-SATTLER (18447288537)
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Bolt Anti-skid Pad Anti-skid Pad Support Plate
F (x4) G (x1) H (x1)
Allen Key 3mm Allen Key 5mm 14-17mm Wrench
P (x1) Q (x1) R (x1)
H
N J
B
ø 10mm
(ø 3/8 ")
G
H
O
N
J R
R
1

Option A : Glass Base Installation

Tear off the protective paper to attach Anti-skid Pad F to the bottom designated position
C
of Base C as image shown.
B
Install the Pole B to the Base C using M5x16 Bolt I and corresponding Bolts E , and
tighten using the Allen Key 3mm P .
B
M4x12 Bolt
M-A (x4)
M4x30 Bolt
M-B (x4)
∅6x∅12.5x13 Spacer
M-C (x4)
2
M
Put the Wire Clip M and Arms A through the Pole B , adjust the preferred height and
B
tighten using Allen Key 5mm Q . Attach the Wire Clip L to the Swivel Arm A .
O
R
L
F
I E
C
P
F
P
G
I
G
C
E
F
A B
Q L A
A
M
Q
B