Sony DVCAM DSR-1800 Operating Instructions Manual page 62

nih
sBunjes nue, p seldeyo
62
TAPE PROTECTION [Tape protct]: Settings related to tape | Description of settings
and video head protection
FROM STOP [> From STOP]: STOP TIMER [>> STP 5 MIN [>>> 5 min] to 0.5 SEC [>>> 0.5 sec]: Select time from
Set the time to switch from timer]: Set the time to 12 settings ranging from 0.5 second to 5 minutes in steps
stop mode to tape protection switch from stop mode of 0.1 second.
mode. to tape protection Factory default setting: 1MIN [>>> 1 min]
mode.
STILL TIMER [>> STL
timer]: Set the time to
switch from still search
mode to tape
protection mode.
NEXT MODE [>> Next
mode]: Select the type
of tape protection
mode to follow still
search mode when the
time set with the STILL
TIMER menu item
elapses.
VIDEO CONTROL [Video]: Settings related to video control | Description of settings
EE DELAY [>EE delay]: An E-E video signal is output delayed | *SYNC DELAY [>> sync]: Delay the sync signal by the
with respect to the video input signal by the time for video corresponding amount of time before attaching it.
circuit processing. With this item, select whether or not to | VIDEO DELAY [>> video]: Attach a sync signal with the same
delay the sync signal attached to the output video signal by timing as the input signal.
an amount corresponding to the video signal delay.
INT VIDEO SG [>Video SG]: Select the test signal to be
output from the internal test signal generator. When SG is
selected using the VIDEO IN button, the internal test signal
generator outputs the selected test signal. This signal can
be recorded.
STD/NON-STD [>STD/N-STD}]: Select the STD or NON-STD
mode in accordance with the composite video or S-video
input.
FROM STILL [> From STILL]:
Set the time to switch from
still search mode to tape
protection mode. Also select
the type of tape protection
mode.
5 MIN [>>> 5 min] to 0.5 SEC [>>> 0.5 sec]: Select time from
12 settings ranging from 0.5 second to 5 minutes in steps
of 0.1 second.
Factory default setting: 1MIN [>>> 1min]
*STEP FWD [>>> Step]: The tape is advanced at "hao times
normal speed for about 2 seconds.
STANDBY OFF [>>> STANDBY]: Standby off mode
*75% COLOR BARS [>>75% bars]: 75% color bar signal
BLACK BURST [>>BB]: Black burst signal
*FORCED STD [>> STD]: The STD mode is always used
(forced STD mode).
FORCED NON-STD [>> NON-STD]: Use this setting when
the input video signal is unstable (forced NON-STD
mode).
*REF VIDEO [>> REF]: Use the signal input to a REF. VIDEO
IN connector as the reference video signal. The input
video signal to be edited is required to be in
synchronization with the reference video signal.
INPUT VIDEO [>> INPUT]: Use the input video signal
selected with the VIDEO IN button in the INPUT SELECT
section.
*OFF [>> OFF]: Do not remove black setup.
ON (REMOVE) [>> ON]: Remove black setup.
OUT REF SEL [>Out Ref.]: Select the reference video signal
to use.
(For DSR-1800 only)
SETUP REMOVE [> Setup rmv]: Determine whether or not to
remove black setup (7.5 IRE) from input analog video
signals when converting them intd digital signals.
(For DSR-1800 only) *OFF [>> OFF]: Do not add black setup.
SETUP ADD [> Setup add]: Determine whether or not to add | ON (ADD) [>> ON]: Add black setup.
black setup to analog video output signals.
(For DSR-1800 only) *OFF [>> OFF]: Do not mute.
CC(F1) BLANK [>CC1 blank]: Select whether to mute the ON [>> ON]: Mute.
closed caption signal to be superimposed on the 1st field
of the output video signal.
(For DSR-1800 only)
CC(F2) BLANK [>CC2 blank]: Select whether to mute the
closed caption signal to be superimposed on the 2nd field
of the output video signal.
*OFF [>> OFF]: Do not mute.
ON [>> ON]: Mute.
Menu Contents