Advertisement
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
VENT
LEVEL
DRAIN
WORM OVER
DRAIN
WORM UNDER
Oil Capacities (ounces) - Standard Units
Mounting
Position
1 - Worm Over
2 - Worm Under
* Shipped Dry
4.
LUBRICATION - The precision - made gears and bearings in our reducers require high-grade lubricants
of the proper
viscosity to maintain trouble- free performance. All standard reducers ordered from the factory are filled with ISO
viscosity grade Mobil Glygoyle 460 polyalkalene glycol (PAG) lubricant. If oil needs to be added or changed,
ONLY compatible polyglycol lubricants should be used. Contact the factory for more information.
TEMPERATURE - Most Titan Units are supplied with wormgear reducers. These units may run at temperatures
5.
between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up). There is NO
NEED TO WORRY unless temperatures exceed 200 degrees F.
6.
GENERAL MAINTENANCE - Regular inspection to insure the reducer bolts and screws are tight, correct alignment
of shaft and/or coupling, no major oil leaks, no excessive heating and no unusual vibration or noise will
insure maximum life and performance of the reducer.
BEARINGS
1.
LUBRICATION - Bearings used on Titan Conveyors are normally pre-lubed for life. If customer requested, re-lube
bearings are provided, the use of a #2 consistency lithium based grease is advised. Greasing Frequency should be
as many times as necessary to maintain a small film of grease leaking at the seals. This will protect against
foreign materials entering the bearing. The following list is provided to aid you in acquiring the proper grease or
an equivalent.
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
Go to Table of Contents
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
Standard Gear Reducer Mounting Positions
& Vent Plug, Level and Drain Locations
VENT
LEVEL
DRAIN
VERTICAL OUTPUT
VENT
LEVEL
LEVEL
DRAIN
VERTICAL INPUT
813 815 818 821 824 826 830 832
4
12
12
20
8
16
20
28
1 gallon = 128 oz. = 231 Cu. in.
NORMAL DUTY
Texaco - Multifak #2
Mobile - Mobilux #2
Amoco - Lithium MP
Shell - Alvania #2
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
DRAIN
VENT
DOUBLE REDUCTION WORM-WORM
* Size 842-860 (far side plug)
Note: High oil level applies to all size 842 & larger
secondary & tertiary units regardless of primary
unit type.
UNIT SIZE
842
852 860
24
40
56
72
112
188 312
40
60
84
108
152
304 328
16 0z. = 1 pint
2 pints = 1 quart
4 quarts = 1 gallon
FIGURE 10
HEAVY DUTY
Sun - Prestige 742EP
Exxon - Lidok #2EP
Arco - Litholene HEP2
Shell - Alvania #2EP
11
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
VENT
VENT
LEVEL*
LEVEL
(All primary units have
their own oil level)
DRAIN
870*
880*
8100*
35
48
72
32-3/4
51-1/4
80
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
7/21
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
Advertisement
