Advertisement
Quick Links
TITAN INDUSTRIES
735 INDUSTRIAL LOOP ROAD
NEW LONDON WI 54961
920-982-6600
800-558-3616 OUTSIDE WI
920-982-7750 FAX
E-MAIL: sales@titanconveyors.com
Website: www.titanconveyors.com
MODEL 102
Conveyor
INSTALLATION, MAINTENANCE AND
PARTS MANUAL
For additional copies of this manual,
please visit our website at
www.titanconveyors.com.
Go to Replacement Parts/Accessories
and select Maintenance Manuals. You can then
select the manual for your model conveyor.
SERIAL NO.
1
5/12
Advertisement
Related Manuals for Titan 102
Summary of Contents for Titan 102
- Page 1 735 INDUSTRIAL LOOP ROAD NEW LONDON WI 54961 920-982-6600 800-558-3616 OUTSIDE WI 920-982-7750 FAX E-MAIL: sales@titanconveyors.com Website: www.titanconveyors.com MODEL 102 Conveyor INSTALLATION, MAINTENANCE AND PARTS MANUAL For additional copies of this manual, please visit our website at www.titanconveyors.com. Go to Replacement Parts/Accessories and select Maintenance Manuals.
- Page 2 (D) No representative of TITAN has been conferred with any authority to waive, alter, vary or add to the terms of warranty state herein, without prior authorization in writing executed by an officer of the company.
- Page 3 With this procedure, we are able to streamline our process and expedite your return. This will require you to call a Titan salesperson prior to your sending back the item to get a RGA number and receive instructions on how to return the item. Other information needed at this time would be your original purchase order number, Titan serial number, job number or invoice number.
- Page 4 Safety The Safety alert symbol is used with the signal words DANGER, WARNING and CAUTION to alert you to safety messages. They are used in safety decals on the unit and with proper operation and procedures in this manual. They alert you to the existence and relative degree of hazards. Understand the safety message.
- Page 5 Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s).
- Page 6 IN ORDER FOR THE CONVEYOR TO BE STABLE, THE SUPPORTS MUST BE WARNING LAGGED TO THE FLOOR OR SUPPORT STRUCTURE. THIS IS THE CUSTOMER RESPONSIBILITY!! FRAME ASSEMBLY To start, along side the area where the conveyor is to be installed, layout the frame sections in their proper position according to the ordered description or refer to your copy of the approval drawing.
- Page 7 COMPONENT CHECKLIST Prior to start up use the following list to double check the conveyor components. MOTOR Have a qualified electrician ensure the motor is wired correctly for your power source. Check that motor is securely fastened to the reducer or motorbase. REDUCER Check that the proper amount of oil is in the reducer.* Make sure a vent plug is installed on the reducer.* (A solid plug is usually installed for shipping.) See FIGURE 9.
- Page 8 BELT TRAVEL STD. TAKE-UP BOTTOM MOUNT GEARMOTOR BELT TRAVEL OPTIONAL SPECIAL TAKE-UP OPTIONAL TOP MOUNTED GEARMOTOR BELT TRAVEL OPTIONAL SIDERAILS OPTIONAL SPECIAL TAKE-UP BOTTOM MOUNT DRIVE FIGURE 6 After making sure the conveyor is cleared off and the drive pulley is moving the belt in the correct direction, run the conveyor.
- Page 9 The first step in belt tracking is to make sure all pulleys are parallel with each other and perpendicular to the frame. Once this has been done refer to FIGURE 7 for proper tracking adjustments. IN REF. TO LEFT HAND AND RIGHT HAND SIDES, WE AT TITAN INDUSTRIES CAUTION...
- Page 10 MOTORS CLEANING - All motors should be kept free of dirt and grease accumulations. Open motors should be periodically vacuumed to remove dust and dirt from the windings. VENTILATION - For best results motors should be operated in an area where adequate ventilation is available.
- Page 11 VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation. Remove the top most drain plug (refer to FIGURE 9 for the position of your reducer) and install the vent plug securely in place.
- Page 12 If oil needs to be added or changed, ONLY compatible polyglycol lubricants should be used. Contact the factory for more information. TEMPERATURE - Most Titan Units are supplied with wormgear reducers. These units may run at temperatures between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up).
- Page 13 V-BELT & SHEAVES If provided on your drive package, V-Belt tension & sheave alignment are important for extended belt life. Read the following list over for proper maintenance or installation. SPAN BELT DEFLECTION 1/64" PER INCH OF SPAN FORCE FIGURE 10 Never pound sheaves on or off a shaft.
- Page 14 SAE 40 120 degrees - 140 degrees F SAE 50 REMEMBER - ALL GUARDS AND BOTTOM PANS, IF PROVIDED, MUST BE DANGER REPLACED BEFORE RUNNING CONVEYOR. TITAN INDUSTRIES IS NOT RESPONSIBLE FOR INJURIES CAUSED BY NOT COMPLYING WITH SAFETY INSTRUCTIONS. 5/12...
- Page 15 MODEL 102 MINI-PRO PRESS CONVEYOR MODEL 102 MINI-PRO PRESS CONVEYOR TOP MT. GEARMOTOR BOTTOM MT GEARMOTOR TOP MOUNT DRIVE (SINGLE PHASE-120 V) (SINGLE PHASE-120 V) (THREE PHASE-208/230/460 V) 15 16 OPTIONAL SIDE TAKE-UP SIDERAILS WELDED TO FRAME 15 16 FRAME WELDMENT...
- Page 16 NEW LONDON WI 54961 920-982-6600 800-558-3616 OUTSIDE WI 920-982-7750 FAX E-MAIL: sales@titanconveyors.com Website: www.titanconveyors.com Contact Your Distributor or Titan Directly for Further Information on Other Titan Conveyor Products Slider bed conveyors Floor to Floor belt conveyors parts conveyors ...