All Reset; Linking Multiple Pre-Amplifiers - TAD -C1000 Owner's Manual

ALL RESET

Pressing the MENU button while holding down the MUTE button when the unit is in standby mode will restore the unit to its
factory default settings.
Factory Default
Input: LINE1
VOLUME: MIN
L-R Balance setting: L/R set 0
Input level setting: 0dB
PASS through setting : No setting
ECO (energy-saving) mode setting
European model:ON
Other model: OFF

Linking multiple Pre-Amplifiers

Using a commercially available Ø 3.5mm stereo mini-cable, the MASTER OUT jack on one Pre-Amplifier can be connected to
the SLAVE IN jack on another Pre-Amplifier, in this way allowing linkage of the input select and sound volume controls of two
or more Pre-Amplifiers.
Using this function, the unit can be combined with a
monaural power amplifier for the ultimate in stereo presence.
Further, by using the units as 4-channel (or more)
Pre-Amplifiers, you can enjoy multichannel playback.
Note that the devices connected to the unit connected to the
SLAVE IN jack will function in the SLAVE mode.
SLAVE mode operations
' When in the SLAVE mode, the display will appear as
follows:
' When the SLAVE mode is enabled, the following functions
can be set via the main unit's keys:
• L-R balance setting, input level setting, PASS through
setting, the ECO (energy-saving) mode.
' In SLAVE mode, the equipment on the SLAVE side is
operated from the equipment on the MASTER side. To
operate the remote control, point it at the device on the
MASTER side.
' When in SLAVE mode, power OFF, volume control, input
switching, mute, and DISP functions are operated by the
MASTER-side device, and cannot be operated from the
SLAVE-side device.
' To set the PASS through setting in SLAVE mode, press the MUTE button on the MASTER side, and then set it on the SLAVE
side.
Note
' When a stereo mini cable is used to connect the MASTER OUT terminal of this unit to the 12 V trigger input terminal of the
TAD product, the power on/standby operation of the TAD product can be performed by operating the power on/standby of
this unit. Be sure to use the proper stereo mini-cable, since use of a monaural mini-cable will cause the generation of noise.
' Since the voltage of the MASTER OUT terminal of this unit is 3.3 V, the above power on/standby operation cannot be
guaranteed when connected to a device with a 12 V trigger input other than a TAD product.
' It is possible to connect two or more Pre-Amplifiers in cascade style, but some operating delay may occur when three or
more are connected in that way.
Speaker L
Power
Amplifier
Stereo mini-cable
MASTER
R L AC IN
LINE 1 LINE 2 LINE 3 LINE 4 LINE 4 LINE 3 LINE 2 LINE 1
MASTER SLAVE
OUT IN
1 2
LINE 1 LINE 2 LINE 3 LINE 4 LINE 5 LINE 6 LINE 6 LINE 5 LINE 4 LINE 3 LINE 2 LINE 1
TAD-C1000
L R
USB XLR COAXIAL OPT 12 V XLR COAXIAL AC IN
D1 D2 D3 D4 TRIGGER
DIGITAL INPUT OUT
R BALANCED L UNBALANCED R L
2
Balanced output
device (CD player, etc.)
Speaker R
Power
Amplifier
SLAVE
R L AC IN
LINE 1 LINE 2 LINE 3 LINE 4 LINE 4 LINE 3 LINE 2 LINE 1
MASTER SLAVE
OUT IN
1 2
LINE 1 LINE 2 LINE 3 LINE 4 LINE 5 LINE 6 LINE 6 LINE 5 LINE 4 LINE 3 LINE 2 LINE 1
TAD-C1000
L R
Unbalanced output device
TAD-C1000
17