Subscribe to Our Youtube Channel
Related Manuals for HEATSTRIP THBBA-UL
Summary of Contents for HEATSTRIP THBBA-UL
- Page 1 Intense with Remote & App Control (THBBA-UL) Product Manual HEATSTRIP® Intense with Remote & App Control www.heatstrip.com US & CANADA...
-
Page 2: Important Instructions
IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: Read all instructions before installing or using this heater. This heater is hot when in use . To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, etc. -
Page 3: Installation
INSTALLATION 1. This equipment shall be installed only by qualified personal who are familiar with the construction and operation of the apparatus and hazard involved. 2. The heater is fitted with an electrical connection box and should be connected as a fixed installation by a licensed electrical professional in accordance with the relevant electrical code. - Page 4 Suitable for permanent outdoor mounting, no protection needed. ® For outdoor applications, the HEATSTRIP Intense with remote & app control (THBBA-UL) is suitable for both permanently exposed (eg. courtyards and patios) and undercover installations - does not need to be fully protected from the elements. Corrosion protection Built from corrosion resistant alloy, it is suitable for use in most applications, including difficult corrosive environments such as coastal areas.
- Page 5 Specifications - Australia VOLTAGE POWER CURRENT DIMENSIONS WEIGHT HEATING MODEL CONNECTION (Watts) (Amps) (mm / in) (kg / lb) AREA (m2 x ft2) THB2200BA-UL 2200 900 x 122 x 90mm Gang Box 5-9m 35.4” x 4.8” x 3.5”in 13lb 54-97ft THB3200BA-UL 3200 13.3...
-
Page 6: Spot Heating Principle
® The top diagram shows how HEATSTRIP Intense with remote & app control is recommended to be used directly over a table, while the bottom diagram indicates how to spot heat a large area. -
Page 7: Selection Guide
Ideal mounting height: 2.2m/7ft to 2.5m/8ft, and the maximum is 2.8m/9ft. Minimum is 2.1m/7ft. • Ideal mounting location: ceiling mounted, directly above area to be heated (e.g. above a table) ® The below table outlines the coverage HEATSTRIP Intense with remote and app model (in m & ft), based on 3 different scenarios. - Page 8 Selection are based on HEATSTRIP Intense being mounted at 2.4m/7.8ft from the floor in a fully enclosed undercover outdoor area.
-
Page 9: Installation Requirements
For mounting heights more than 2.8m/9ft outdoors, we recommend the use of the optional accessories to reduce the ® height of the heater to 2.3m—2.5m/8-9ft. This will increase the effectiveness of your HEATSTRIP . Refer to the Mounting Accessory section for more information. -
Page 10: Installation Location
Installation location — the below diagrams confirm the minimum recommended clearances. Angled Wall 300mm / 12” Installation Surface Lights, fans, and sprinklers Below Ceiling Installation 300mm / 12” 1000 min. 1000mm / 40” Surface Lights, fans, and sprinklers Below... -
Page 11: Mounting Options
Mounting options ® The installation of HEATSTRIP Intense with remote & app (THB-BA-UL) is simple and easy with the standard mounting brackets supplied. For other more challenging locations there are a range of mounting options available - refer to below diagrams. -
Page 12: Standard Mounting Brackets
Standard mounting brackets ® The HEATSTRIP Intense with remote & app control comes with a pair of standard mounting brackets. These adjustable brackets allow direct ceiling or wall mount, and come with pre-set angle options of parallel, 22.5° and 45°. - Page 13 MOUNTING Fix the two mounting brackets to the ceiling or wall in the desired location (refer minimum bracket centre chart). Make sure the method of fixing (bolts or screws) will be more than strong enough to support the weight of the heater, allowing for strong winds and other conditions.
-
Page 14: Extension Mount Bracket
Extension Mount Bracket ® The Extension Mount bracket allows HEATSTRIP Intense units to be lowered from high ceilings using rigid connections. The standard length options as part of the kit are 150mm (5.9”) 300mm (11.8”), 600mm (23.6”), 900mm (35.4”) and 1200mm (47.2”). -
Page 15: Flush Mount Enclosure
Flush mount enclosure ® The Flush Mount Enclosure is an ideal way to neatly install the HEATSTRIP into a ceiling. They are available for the ® HEATSTRIP Intense with Remote & App model, and are supplied as a one-piece unit suitable for mounting individual heaters. -
Page 16: Remote Control Operation
Remote Control Operation Receiver • Receiver is located on the heater. Signal Transmitter • To use the remote controller, aim the transmitter to the heater. A line of sight Temperature Control Button transmission is required for the unit to function. •... - Page 17 (Make sure Wi-Fi is TuyaSmart App enabled) Connect the HEATSTRIP Heater to Once the power is switched on, hold the + button Power. (Either Plug-In or Hardwired) on the remote until the LED screen is blinking CC. Open the App and Select Device Type select “Add Device”...
- Page 18 Pair the Google device to the Google Home App Once paired, click on the Tuya Smart App Select “Me” Select “Google Assistant” Select “Link with Google Assistant” Select “Agree and link” Choose device “Select HEATSTRIP Intense with Remote & App Pairing completed...
- Page 19 CHECK END SYMPTOM REASON CHECK TECHNICIAN USER Take photos of Damaged during Inspect units for Return to factory for repair/ Freight damage packaging and unit and transport damage replacement return to factory Parts missing from Contact factory for Missing brackets replacement brackets No power to unit or Check that there...
-
Page 20: Maintenance
Carrying out the cleaning process at least every three months will reduce the amount of build up and keep the Heatstrip in good condition. If the heater is in a corrosive environment eg. salt spray, we recommend that you clean your heater with a light spray of fresh water every week. - Page 21 CHECK END SYMPTOM REASON CHECK TECHNICIAN USER Take photos of Damaged during Inspect units for Return to factory for repair/ Freight damage packaging and unit and transport damage replacement return to factory Parts missing Contact factory for Missing brackets from box replacement brackets No power to unit Check that there...
-
Page 22: Warranty Terms And Conditions
The below Warranty Terms and Conditions apply for International Customers. ® Thermofilm warrants to the original owner that HEATSTRIP Enhance with Remote and App control products will be free from defects in materials and workmanship for a period of 12 months from the date of purchase in accordance with the following warranty terms and conditions.
Need help?
Do you have a question about the THBBA-UL and is the answer not in the manual?
Questions and answers