Related Manuals for HEATSTRIP Classic
Summary of Contents for HEATSTRIP Classic
- Page 1 Classic (THH-A) Product Manual HEATSTRIP® Classic (THH-A) www.heatstrip.com.au Ph: 03 9562 3455 E: sales@thermofilm.com.au...
- Page 2 2.5m (THS800A) or 2.7m (all other THS-A models). ® HEATSTRIP Classic (THHA & THHA-R models) is a premium high temperature heater and is primarily used for protected outdoor areas with an ideal mounting height of 2.3m to 2.5m and maximum mounting height of 2.7m. ®...
- Page 3 The standard HEATSTRIP Classic is controlled by a simple on/off operation, either when plugged directly into a power point, or hard- wired via a wall mounted on/off switch. The unit takes approximately 15 minutes to heat up to maximum temperature and approximately 30 minutes to cool down, depending upon the ambient temperature.
- Page 4 2.7 m in a fully enclosed outdoor area (For higher ceiling heights, units can be lowered using optional bracket kits or refer to the Heatstrip Max range) MOUNTING OPTIONS Suitable for ceiling, wall, beam, fixed umbrella and recess mounting. Also available for extension mount using rigid fixing poles and chain mount bracket.
- Page 5 HEATSTRIP , but you never have to worry about running out ® of gas, no refilling, no unattractive gas bottle to waste space; and HEATSTRIP actually improves the value of your property.
-
Page 6: Spot Heating Principle
Option 1 and 2 show a comparison between heating an entire area or spot heating over a table. ® The bottom layout shows the flexibility of using HEATSTRIP to provide a comfortable environment, even when the layout of the area is very unusual. -
Page 7: Radiant Footprint
The diagram to the left shows the radiant ® footprint of HEATSTRIP Classic, and is an approximate guide based on a fully enclosed outdoor environment. This diagram shows that the maximum heat output is found directly under the heater, and the temperature decreases as you move away from the heater. -
Page 8: Selection Guide
The table below outlines the coverage of each HEATSTRIP Classic model based on 3 different scenarios with di- rect overhead mounting. For example, for an outdoor area that is protected from prevailing winds by walls, café blinds etc, Model THH 1500A will cover 3m and Model THH2400A will cover 4.8m... - Page 9 ® Selections are based on HEATSTRIP Classic being mounted at 2.4m from the floor in a fully enclosed undercover outdoor area. 1 x THH1800A 1 x THH3200A...
-
Page 10: Installation Requirements
Installation Requirements ® The ideal mounting position for the HEATSTRIP Classic is on the ceiling directly above the area to be heated. If this is ® not possible, HEATSTRIP can be mounted on a wall and angled downwards. In this situation, ensure the mounting height is in the range of 2.1m to 2.7m and the table is within 2.5m of the wall. -
Page 11: Installation Location
Installation location — the diagrams below provide the minimum recommended clearances in mm. WARNING: This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided. -
Page 12: Mounting Options
The HEATSTRIP Classic can be mounted directly to the ceiling, angled downwards on a wall, fitted flush with the ceiling, suspended on chains or poles, attached to beams or poles, mounted end-to-end, or 2 units side-by-side together. Refer to the... -
Page 13: Standard Mounting Brackets
Standard mounting brackets ® The HEATSTRIP Classic comes with a pair of standard mounting brackets. These adjustable brackets allow direct ceiling or wall mount, and come with preset angle options of parallel, 22.5° and 45°. “X” MODEL MINIMUM DISTANCE (mm) -
Page 14: Flush Mount Enclosure
® all HEATSTRIP Classic models, and are supplied as a one-piece unit suitable for mounting individual heaters. Flush mounting can be used with plaster or timber lined ceiling materials. An ideal mounting height is 2.3m-2.5m, with a maximum ceiling height of 2.7m in an outdoor enclosed environment. - Page 15 HEATSTRIP Wall Mounting Kit - (THHAC-028) HEATSTRIP Wall Mounting Kit is an ideal way to install units into hard to mount applications where wall mounting is preferable to direct overhead mounting, applications include heating over tables, lounges, work stations etc. These kits are suitable for all HEATSTRIP Elegance &...
-
Page 16: Extension Mount Bracket
The Extension Mount bracket allows HEATSTRIP Classic units to be lowered from high ceilings using rigid connections. The brackets are designed to be used with 20mm x 20mm x 1mm tube (SHS), and can be supplied as brackets only for customis- ing the length of the drop on site, or supplied as a complete kit with brackets, pre-cut poles and connections. - Page 17 Permanent Umbrella Mounting Guide ® HEATSTRIP Classic heaters can be mounted underneath most commercial grade, permanent umbrella’s or shade structures. The material must protect the heater from direct rainfall. All models can be connected to the horizontal umbrellas struts, using the Pole/Beam mounting kit (THHAC-001).
-
Page 18: Maintenance
Carrying out the cleaning process at least every three months will reduce the amount of build up and keep the Heatstrip in good condition. If the heater is in a corrosive environment eg. salt spray, we recommend that you clean your heater with a light spray of fresh water every week. - Page 19 HEATSTRIP Plug In Remote Controller The TT-MTR-PLUG has been designed to provide easy remote control timer ® functionality to wall socket powered HEATSTRIP heaters. The unit can however be used to remotely operate with timer functionality any device pow- ered by a standard 10A Australian wall socket outlet.
- Page 20 Wall Controller with Remote TT-MTM2 Wall Controller This controller is a custom designed and manufactured controller for HEATSTRIP heaters. It has been designed for ease of use and to provide low running costs of your heater. It provides both temperature control (allowing the user to turn the heat output up or down depending on the ambient temperature and conditions) and a timer for automatic heater shut-off operation.
-
Page 21: Operation
Operation Press “On/Off” button to turn power on and off. Once turned on, the controller will default to High power setting and will be permanently on (no timer function). Press “POWER” button to select the desired power setting by cycling through HIGH—MEDIUM -LOW. - Page 22 TT-MTM CONTROLLER INSTALLATION GUIDE Controller Wiring Example Load 16A Max GANG 220-240V~ 50Hz Supply The TT-MTM2 Controller required sufficient air circulation in order to provide continuous operation on the high power load setting. The vents must always remain clear; never block or cover the vents. An ideal controller installation will provide significant space around the back of the controller.
- Page 23 Heater wiring schematic diagrams It is recommended to install an ON/OFF isolation switch before the controller and ensure the unit is turned OFF after use. Multiple heaters can be operated using a single controller, however the maximum current rating of 16A must not exceeded.
-
Page 24: Warranty Terms And Conditions
® Thermofilm warrants to the original owner that HEATSTRIP products will be free from defects in materials and workmanship for a period of 12 months from the date of purchase in accordance with the following warranty terms and conditions.
Need help?
Do you have a question about the Classic and is the answer not in the manual?
Questions and answers