Grizzly G0967 Owner's Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Sander
  5. G0967
  6. Owner's manual
Grizzly G0967 Owner's Manual

Grizzly G0967 Owner's Manual

20" variable-speed disc sander
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL G0967
20" VARIABLE-SPEED
DISC SANDER
OWNER'S MANUAL
(For models manufactured since 06/23)
COPYRIGHT © MAY, 2023 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#CS22710 PRINTED IN CHINA
V1.05.23
***Keep for Future Reference***

Advertisement

Table of Contents
loading

Related Manuals for Grizzly G0967

Summary of Contents for Grizzly G0967

  • Page 1 (For models manufactured since 06/23) COPYRIGHT © MAY, 2023 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #CS22710 PRINTED IN CHINA V1.05.23...
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

  • Page 3: Table Of Contents

    Table of Contents INTRODUCTION ..........................2 Contact Info ..........................2 Manual Accuracy ........................2 Identification ..........................3 Controls & Components ......................4 Machine Data Sheet ........................5 SECTION 1: SAFETY ........................7 Safety Instructions for Machinery ....................7 Additional Safety for Disc Sanders .................... 9 SECTION 2: POWER SUPPLY ......................

  • Page 4: Introduction

    Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equip- ment, or poor work results. Model G0967 (Mfd. Since 06/23)

  • Page 5: Identification

    Wear eye protection. b) Support workpiece with miter gauge, backstop, or work table. c) Maintain ⁄ in. maximum clearance between table and sanding disc. d) Avoid kickback by sanding in accordance with directional arrows. Model G0967 (Mfd. Since 06/23)

  • Page 6: Controls & Components

    C. ON Button: Turns motor ON. 90° Stop Screw: Stops table tilt at 90°. D. OFF Button: Turns motor OFF. 45° Stop Screw: Stops table tilt at 45°. Model G0967 (Mfd. Since 06/23)

  • Page 7: Machine Data Sheet

    MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0967 20" VARIABLE‐SPEED DISC SANDER Product Dimensions: Weight................................309 lbs. Width (side-to-side) x Depth (front-to-back) x Height............... 27-1/2 x 27 x 48-1/2 in.
  • Page 8 The information contained herein is deemed accurate as of 7/6/2023 and represents our most recent product specifications. Model G0967 PAGE 2 OF 2 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. Model G0967 (Mfd. Since 06/23)

  • Page 9: Section 1: Safety

    Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. Model G0967 (Mfd. Since 06/23)
  • Page 10 Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. Model G0967 (Mfd. Since 06/23)

  • Page 11: Additional Safety For Disc Sanders

    Minimize this risk by adjusting which decreases risk of long-term respiratory dam- table no more than ⁄ " away from sandpaper. age, but it is not a substitute for using a respirator. Model G0967 (Mfd. Since 06/23)

  • Page 12: Section 2: Power Supply

    To reduce the risk of these hazards, avoid over- loading the machine during operation and make sure it is connected to a power supply circuit that meets the specified circuit requirements. -10- Model G0967 (Mfd. Since 06/23)
  • Page 13 Minimum Gauge Size ......18 AWG all local codes and ordinances. Maximum Length (Shorter is Better)..50 ft. -11- Model G0967 (Mfd. Since 06/23)

  • Page 14: Section 3: Setup

    IMPORTANT: Save all packaging materials until you are completely satisfied with the machine and have resolved any issues between Grizzly or the shipping agent. You MUST have the original pack- aging to file a freight claim. It is also extremely Wear safety glasses during helpful if you need to return your machine later.

  • Page 15: Inventory

    If you cannot find an item on this list, care- fully check around/inside the machine and packaging materials. Often, these items get lost in packaging materials while unpack- ing or they are pre-installed at the factory. Figure 5. Main inventory. -13- Model G0967 (Mfd. Since 06/23)

  • Page 16: Cleanup

    Figure 7. T23692 Orange Power Degreaser. Repeat Steps 2–3 as necessary until clean, then coat all unpainted surfaces with a quality metal protectant to prevent rust. -14- Model G0967 (Mfd. Since 06/23)

  • Page 17: Site Considerations

    Only install in an Shadows, glare, or strobe effects that may distract access restricted location. or impede the operator must be eliminated. 39½" Electrical Connection Dust Port 37½" 27½" 27" Figure 8. Minimum working clearances. -15- Model G0967 (Mfd. Since 06/23)

  • Page 18: Assembly

    Cabinet Door Figure 11. Lifting locations. Tip: Route additional ratchet strap around machine base to keep lifting straps from mov- Figure 9. Location of cabinet door. ing to keep machine weight evenly distributed. -16- Model G0967 (Mfd. Since 06/23)
  • Page 19 12. Loosen (2) table tilt lock handles, adjust table tilt to 0°, then tighten lock handles (see Figure 13). Table Tilt Lock Handle (1 of 2) Table Figure 15. Example of installing sanding disc. Figure 13. Table tilt adjusted to 0°. -17- Model G0967 (Mfd. Since 06/23)

  • Page 20: Dust Collection

    22. Install disc guard, ensuring guard does not contact sanding disc. Figure 17. Example of dust hose attached to dust port. Tug hose to make sure it does not come off. Note: A tight fit is necessary for proper performance. -18- Model G0967 (Mfd. Since 06/23)

  • Page 21: Test Run

    Clear all setup tools away from machine. out (see Figure 20). This resets switch so machine can start. Press Stop button in (see Figure 18). Turn variable-speed dial all the way counter- clockwise (see Figure 18). Figure 20. Resetting switch. -19- Model G0967 (Mfd. Since 06/23)
  • Page 22 — If machine does start, immediately turn it OFF and disconnect power. Safety feature of Stop button is NOT working properly and must be replaced before further using Figure 22. Location of disc rotation arrow. machine. -20- Model G0967 (Mfd. Since 06/23)

  • Page 23: Section 4: Operations

    Read books/magazines or get formal training before beginning any proj- ects. Regardless of the content in this sec- tion, Grizzly Industrial will not be held liable for accidents caused by lack of training. Keep hair, clothing, and jewelry away from mov- ing parts at all times.

  • Page 24: Sanding Tips

    Sanding Tips Choosing Sandpaper • Extend the life of the sandpaper by regularly The Model G0967 uses a 20" sanding disc. using PRO-STIK® abrasive surface cleaners Below is a chart that groups abrasives into differ- (see Accessories on Page 27).

  • Page 25: Workpiece Inspection

    Workpiece Adjusting Table Tilt Inspection The angle of the table on the Model G0967 can be adjusted between 0°–45° to sand angled Some workpieces are not safe to sand or may workpieces. require modification before they are safe to sand.

  • Page 26: Adjusting Miter Gauge

    Miter Gauge Sanding Disc The miter gauge angle can be adjusted 60° to the The G0967 accepts 20" diameter PSA (pressure- right or the left, keeping angled workpieces accu- sensitive adhesive) sanding discs. Use the fol- rate. When the miter lock knob is tight, both the...
  • Page 27 13. Install disc guard, ensuring guard does not contact sanding disc. Figure 28. Example of installing sanding disc. -25- Model G0967 (Mfd. Since 06/23)

  • Page 28: Sanding Operations

    Sanding Operations The Model G0967 uses a dual-axis miter slot design for increased workpiece control. Always keep disc guard in place and workpiece on side of wheel that is rotating downward. This will reduce likelihood of workpiece ejection. Figure 30. Example of X-axis sanding.

  • Page 29: Section 5: Accessories

    Refer to our website or latest catalog for additional recommended accessories. Grizzly 20" Sanding Discs These tough, aluminum oxide sanding discs come in a variety of grits to fit the Model G0967. These sanding discs are pre-applied with top-quality pressure-sensitive adhesive. D1342—60-Grit, 2-Pk.
  • Page 30 Measures 3' wide x 5' long x ⁄ " thick. D4256 D4206 W1017 W1053 Figure 39. T10456 Anti-Fatigue Mat 3' x 5'. W1317 W1007 Figure 37. Dust collection accessories. www.grizzly.com 1-800-523-4777 order online at or call -28- Model G0967 (Mfd. Since 06/23)

  • Page 31: Section 6: Maintenance

    To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, Cleaning the Model G0967 is relatively easy. maintenance, or service. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any...

  • Page 32: Section 7: Service

    5. Motor bearings at fault. 5. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement. 1. Correct phase polarity (Page 20). Machine 1. Motor power connections wired out of phase. operates in reverse. -30- Model G0967 (Mfd. Since 06/23)
  • Page 33 2. Replace sanding disc (Page 24). Store sanding disc flat, not folded or bent. Workpiece 1. Not supporting workpiece properly. 1. Use miter gauge to support workpiece. frequently gets pulled out of your hands. -31- Model G0967 (Mfd. Since 06/23)

  • Page 34: Adjusting Table Gap & Parallelism

    Figure 40. Location of disc guard and fasteners. touch table at any point in its rotation. Loosen (6) cap screws shown in Figure 41. Install disc guard, ensuring guard does not contact sanding disc. -32- Model G0967 (Mfd. Since 06/23)

  • Page 35: Calibrating Miter Gauge Scale

    Square Table Tilt Lock Handle (1 of 2) 90° Stop Screw Indicator 90° Square Miter Gauge Figure 44. Squaring table to sanding disc. Body Figure 43. Example of miter gauge square to sanding disc. -33- Model G0967 (Mfd. Since 06/23)
  • Page 36 Adjust 45° stop screw until table is exactly 45° to disc, then tighten jam nut on 45° stop To calibrate 45° stop screw: screw without turning stop screw to secure setting. DISCONNECT MACHINE FROM POWER! -34- Model G0967 (Mfd. Since 06/23)

  • Page 37: Section 8: Wiring

    Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -35- Model G0967 (Mfd. Since 06/23)

  • Page 38: Wiring Diagram

    TA TB TC DO1 24V CM DI1 DI2 DI3 DI4 DI5 DI6 10V AI1 AI2 GNDAO1AO2 GOCHENG GB2N-GS Circuit Breaker JUCHE DZ47-63 C2 Power Switch Circuit Breaker JUCHE JFD11-25 Transformer TTMC COD.045/90 JUCHE DZ47-63 C16 Braking Resistor 500W 80Ω READ ELECTRICAL SAFETY -36- Model G0967 (Mfd. Since 06/23) ON PAGE 35!

  • Page 39: Electrical Component Photos

    Electrical Component Photos Figure 48. Motor wiring. Figure 49. Control panel wiring. Figure 50. Electrical cabinet. READ ELECTRICAL SAFETY -37- Model G0967 (Mfd. Since 06/23) ON PAGE 35!

  • Page 40: Section 9: Parts

    SECTION 9: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability. Main 23-3 23-1 23-2 23-5...
  • Page 41 LOCK NUT M8-1.25 P0967046 FOOT M10-1.5 X 50 P0967096 HINGE P0967047 FOOT PAD P0967097 FLAT HD CAP SCR M5-.8 X 10 P0967048 CABINET BUY PARTS ONLINE AT GRIZZLY.COM! -39- Model G0967 (Mfd. Since 06/23) Scan QR code to visit our Parts Store.

  • Page 42: Labels & Cosmetics

    Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -40- Model G0967 (Mfd.

  • Page 43: Warranty & Returns

    WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.

Table of Contents