Preparation And Usage Of This Device - Microlife NEB 400 Manual

 Before plugging in the device, make sure that the electrical
rating, shown on the rating plate on the bottom of the unit, corre-
sponds to the mains rating.
 In case the power plug provided with the device does not fit your
wall socket, contact qualified personnel for a replacement plug
with that of a suitable one. In general, the use of adapters,
simple or multiple, and/or extension cables is not recom-
mended. If their use is indispensable, it is necessary to use
types complying with safety regulations, paying attention that
they do not exceed the maximum power limits, indicated on
adapters and extension cables.
 Do not leave the unit plugged in when not in use; unplug the
device from the wall socket when it is not in operation.
 The installation must be carried out according to the instructions
of the manufacturer. An improper installation can cause
damage to persons, animals or objects, for which the manufac-
turer cannot be held responsible.
 The power cord of this device cannot be replaced by the user.
In case of a power cord damage, address to a technical service
center authorized by the manufacturer for its replacement.
 The power supply cord should always be fully unwound in order
to prevent dangerous overheating.
 Before performing any maintenance or cleaning operation, turn
off the device and disconnect the plug from the main supply.
 Some parts of the unit are so small that they may be swallowed
by children; keep the equipment out of children's reach.
 If you decide not to use the device any longer, it is recom-
mended to dispose of it according to the current regulations.
 Make sure to:
 use this device only with medicines prescribed by your
doctor;
 make the treatment using only the accessory recommended
by your doctor depending on the pathology;
 use the nosepiece accessory only if expressly indicated by
your doctor and paying attention to NEVER introduce the
bifurcations in the nose, but only bringing them as close as
possible.
 Check in the medicine instruction leaflet for possible contraindi-
cations for use with common aerosol therapy systems.
 To avoid strangulation and entanglement, keep cable and air
tubes out of reach of young children.
Microlife NEB 400
 Do not position the equipment so that it is difficult to operate
the disconnection device.
 Nebuliser and accessories are single patient use. Device is
multi-patient use.
 This nebulising system is not suitable for use in anaesthetic
breathing system or a ventilator breathing system. The patient
cannot undergo MRI scan while using this device.
 This device is designed to nebulise solution and suspension
liquids.
 Do not use this device if you think it is damaged or notice
anything unusual.
 This device comprises sensitive components and must be
treated with caution. Observe the storage and operating condi-
tions described in the «Technical specifications» section.
 The use of this device is not a replacement for visiting the
doctor. In case of no health improvement after treatment
consult your doctor again.
This device is not a toy! Keep out of reach of children and
do not leave children alone during treatment.

2. Preparation and usage of this device

 The device must be checked before each use in order to identify
any malfunctions and/or damage caused during transportation
and/or storage. During inhalation, sit upright and relaxed to
avoid compressing the airways and impairing treatment effec-
tiveness. The accessories must be used only with a single
patient, it is not recommended to use them with several
patients.
 After unpacking the device, check it for visible damages or
defects; pay particular attention to cracks in the plastic housing,
which may expose electrical components. Check if the acces-
sories are intact.
 Before using the device, proceed with the cleaning operations
as described in the chapter «Cleaning and disinfecting».
1. Assemble the nebuliser kit AK. Ensure that all parts are
complete.
2. Fill the nebuliser with the inhalation solution as per your doctor's
instructions. Ensure that you do not exceed the maximum level.
3. Connect the nebuliser with the air tube 6 to the compressor 1
and plug the power lead 2 into the socket (230V 50 Hz AC).
4. To start the treatment, set ON/OFF switch 3 into the «I» posi-
tion.
EN
3