EPOMAKER EP87 - 87-key three-mode hot-swappable mechanical keyboard Manual

MAC MODES

WIN MODES

QUICK FUNCTION

RGB LIGHT EFFECT CONTROL

WIRELESS CONNECTION

PAIRING WIRELESS 2.4GHz

1. Power on the keyboard
2. Short press FN+4 to enter 2.4G mode
3. FN+4 combination key 3S to enter pairing mode
4. Insert the receiver, the indicator light flashes quickly
5. After the pairing is successful, exit the code matching, and the mode light will always be on for 2S

30s after the paired device is notfound, the exit code matching mode light goes out and the keyboard goes to sleepAfter the pairing is successful, let stand for 2 minutes to enter the light sleep state, andthe keyboard enters deep sleep after 10 minutes from entering the light sleep state.

PAIRING BLUETOOTH

1. Power on the keyboard
2. Short press FN+1/2/3 key combination to enter Bluetooth mode
3. Long press the FN+1/2/3 key combination for 3S, the keyboard enters the code matching state, and the indicator light flashes quickly
4. Connected to the device, the indicator light is always on for 2S

If the device is not connected, the indicator light goes out, and the keyboard goes to sleep After the pairing is successful, let it stand for 2 minutes to enter the light sleep state, and the keyboard enters deep sleep after 15 minutes from entering the light sleep state

BATTERY POWER

1. The battery is below 10%, and the space flashes
2. The space is always on during charging
3. Restore the current backlight mode after full

PRODUCT SPECIFICATIONS

REPLACING KEYCAPS AND SWITCHES

For a full guide on how to remove keycaps and switches scan the QR Code or type in your browser: https://epomaker.com/blogs/guides/diy-guide-how-to-remove-and-replace-your-mechanical-keyboard-switches

Before installing switches, be sure the pins are clean and straight.

Push Straight Down
Please be gentle. Be sure the pins are aligned with the slots.

Included Tools

Mechanical Switch
Example of a switch as seen from top after you remove the keycap to prepare for switch removal.

The Switch Puller tool aligns Vertically to the Switch to unclip the plastic securing the switch to the plate.

Remove Switches

1. Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
2. Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
3. Using firm but gentle force pull the switch away from the keyboard using a vertical motion.

Install Switches

1. Check that all the switch metallic pins are perfectly straight and clean.
2. Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
3. Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
4. Inspect the switch to ensure it's properly attached to your keyboard, and test it.

Note: If the key doesn't work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process.
Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid damage to the keyboard due to operating errors.

TECHNICAL ASSISTANCE

For technical assistance, please email to support@epomaker.com with your purchase order number and a detailed description of your issue.
We normally respond to enquiries within 24 hours. If you purchased your keyboard from a distributor or not from any official store of Epomaker, please contact them directly for any additional help.

COMMUNITY FORUMS
Join our community and learn together with other keyboard enthusiasts.
https://discord.gg/2q3Z7C2
https://www.reddit.com/r/Epomaker/

Made in China
Manufacturer: Shenzhen Changyun Technology Co., Ltd.
Address: Seventh Floor, Kai Daer Building, No.168 Tongsha Road, Xili Street, Nanshan Disctrict, Shenzhen, Guangdong, CN
Email: support@epomaker.com
Web: www.epomaker.com

APEX CE SPECIALISTS LIMITED
Address: UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD CORK, T23 AT2P, IRELAND
Contact: Wells
Tel: +353212066339
Email: info@apex-ce.com