EPOMAKER EP108 - Wireless Mechanical Gaming Keyboard Manual

Also See for EP108:

Quick start manual (6 pages)

Table of Contents

Contents

1 WIN MODES
2 MAC MODES
3 CONNECTION MODE
4 RGB SETTINGS
5 SWITCH THE CONNECTED DEVICE
6 PAIRING BLUETOOTH
7 PAIRING WIRELESS 2.4GHz
8 POWER SAVE MODE
9 SPECIFICATION PARAMETER
10 REPLACING KEYCAPS AND SWITCHES
11 TECHNICAL ASSISTANCE
12 Documents / Resources
- 12.1 References
- 12.2 Download manual

EPOMAKER EP108 - Wireless Mechanical Gaming Keyboard Manual

WIN MODES

Fn+Esc (5s)	Reset
Fn+Win	Win Lock
Fn+S	MAC Modes
Fn+PgUp	Power Saving
Fn+0 (numpad)	Battery Percentage
Fn+F1	My Computer
Fn+F2	Browser
Fn+F3	Computer Management
Fn+F4	Files
Fn+F5	Email
Fn+F6	Home Page
Fn+F7	Previous Track
Fn+F8	Play/Pause
Fn+F9	Next Track
Fn+F10	Search
Fn+F11	Lock Screen
Fn+F12	Lock Keyboard

MAC MODES

Fn+Esc (5s)	Reset
Fn+Win	Win Mode
Fn+S	MAC Modes
Fn+PgUp	Power Saving
Fn+0 (numpad)	Battery Percentage
F1	Brightness -
F2	Brightness +
F3	Task Manager
F4	Siri
F5	-
F6	-
F7	Previous Track
F8	Play/Pause
F9	Next Track
F10	Mute
F11	Volume -
F12	Volume +

CONNECTION MODE

Fn+1	BT1
Fn+2	BT2
Fn+3	BT3
Fn+4	2.4G
Fn+5	Wired

RGB SETTINGS

Fn+Backspace	RGB Backlight On/Off
Fn+Ins	Change Backlight Effect
Fn+Home	Change Backlight Color
Fn+Del	Light Effect Direction
Fn+←→	Light Speed Adjustment
Fn+↑↓	Brightness Adjustment

SWITCH THE CONNECTED DEVICE

Short press Fn+1/2/3/4/5 to switch the device connection mode
The indicator light flashes slowly during the connection process of the device, and the indicator light stays on for 2s after the connection is successful
If the connection fails, the indicator light goes out and the keyboard sleeps

PAIRING BLUETOOTH

After the keyboard is turned on, press and hold Fn+1/2/3 until the indicator light flashes quickly to enter pairing mode
Find the KC108 BT3.0/5.0 on the bluetooth receiving device and pair it with it. After the pairing is completed, the indicator light is always on for 2s
If the pairing fails, the keyboard indicator turns off and goes to sleep, please re-pair

PAIRING WIRELESS 2.4GHz

Press and hold 4 until the pairing indicator flashes quickly to enter the 2.4G pairing mode
Insert the 2.4G receiver and place the keyboard as close to the 2.4G receiver as possible
After the code matching is successful, exit the code matching, the mode light is always on for 10s
If the code matching device is not found successfully, the indicator light turns off and goes to sleep after 30s, please perform the code matching operation again.

POWER SAVE MODE

When wirelessly connected (Bluetooth/2.4G), turn off the backlight without any operation for 5 minutes, and enter into deep sleep without operation for 30 minutes Press Fn+PGUP to enter the battery saving mode.

SPECIFICATION PARAMETER

KEYS AMOUNT:	108 Keys
KEYCAPS:	PBT
HOTSWAP:	YES
LIGHT:	RGB
BATTERY CAPACITY:	6200mAh
CONNECTIVITY:	Type-C Wired & Bluetooth Wireless
COMPATIBILITY:	Windows/Mac
DIMENSION:	440mm×130mm×28mm
WEIGHT:	1030±20g

REPLACING KEYCAPS AND SWITCHES

For a full guide on how to remove keycaps and switches scan the QR Code or type in your browser: https://epomaker.com/blogs/guides/diy-guide-how-to-remove-and-replace-your-mechanical-keyboard-switches

Before installing switches, be sure the pins are clean and straight.

Push Straight Down
Please be gentle. Be sure the pins are aligned with the slots.

Included Tools

Mechanical Switch
Example of a switch as seen from top after you remove the keycap to prepare for switch removal.

The Switch Puller tool aligns Vertically to the Switch to unclip the plastic securing the switch to the plate.

Remove Switches

Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
Using firm but gentle force pull the switch away from the keyboard using a vertical motion.

Install Switches

Check that all the switch metallic pins are perfectly straight and clean.
Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
Inspect the switch to ensure it's properly attached to your keyboard, and test it.

caution Note: If the key doesn't work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process.
Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid damage to the keyboard due to operating errors.

TECHNICAL ASSISTANCE

For technical assistance, please email to support@epomaker.com with your purchase order number and a detailed description of your issue.
We normally respond to enquiries within 24 hours. If you purchased your keyboard from a distributor or not from any official store of Epomaker, please contact them directly for any additional help.

COMMUNITY FORUMS
Join our community and learn together with other keyboard enthusiasts.
https://discord.gg/2q3Z7C2
https://www.reddit.com/r/Epomaker/

Made in China
Manufacturer: Shenzhen Changyun Technology Co., Ltd.
Address: Seventh Floor, Kai Daer Building, No.168 Tongsha Road, Xili Street, Nanshan Disctrict, Shenzhen, Guangdong, CN
Email: support@epomaker.com
Web: www.epomaker.com

APEX CE SPECIALISTS LIMITED
Address: UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD CORK, T23 AT2P, IRELAND
Contact: Wells
Tel: +353212066339
Email: info@apex-ce.com