EPOMAKER EP75 - Hot-Swap Wired/Wireless Mechanical Keyboard Quick Manual

WINDOWS SHORTCUT

MAC SHORTCUT

FUNCTION KEY COMBINATIONS

LIGHT EFFECTS

FN + HOME	RGB Effects 1-5
FN + PGUP	RGB Effects 6-10
FN + END	RGB Effects 11-15
FN + PGDN	RGB Effects 16-20
FN + \|	Toggle Backlight colors
FN + L	Turn on/off Backlights
FN + L_CTRL	Toggle Sidelight Effect and Off
FN + L_ALT	Toggle Sidelight Colors
FN +	Backlights Brightness -
FN +	Backlights Brightness +
FN +	Dynamic light direction to left
FN +	Dynamic light direction to right
FN + -_	Backlights Speed-
FN + =+	Backlights Speed +
FN + Z	Toggle Sidelight Brightness
FN + X	Toggle Sidelight Speed

CHANGE RGB EFFECTS

Press Fn + Home/PgUp/End/PgDn to switch the RGB effects of your Epomaker Aura75 keyboard.

PAIRING BLUETOOTH

Toggle the switch on the right side of the keyboard to make sure that the keyboard is under the Bluetooth mode:

1. Hold Fn+1!/2@/3# for 3-5 seconds till the indicator flashes fast in red/green/yellow the keyboard is ready to pair.
2. Turn on your Bluetooth device and find 'Aura75 BT3.0' or 'Aura75 BT5.0-1/2/3', then connect. When the keyboard is connected to the Bluetooth device, the light on the 1!/2@/3# key stops flashing and the connection is done.
3. Press Fn+1!/2@/3# to toggle between the Bluetooth devices 1/2/3.

PAIRING WIRELESS 2.4GHZ

1. Press Fn + 4$ the indicator flashes in green, the keyboard is under the 2.4G mode;
2. Continue to hold Fn+4$ for 3-5 seconds till the 4$ indicator flashes fast, the keyboard is ready to pair;
3. Insert the 2.4G dongle to your device, the 4$ key stops flashing and the connection is done.

WIRED MODE

Press Fn+5%, the keyboard goes to the wired mode successfully.

KNOB

Clockwise: Volume - / Backlight Brightness -
Counterclockwise: Volume + / Backlight Brightness +
Press knob: Toggle the knob function between volume or backlight brightness control.

CHECK BATTERY

Hold Fn+Backspace, the keys from 1! to 0) lights up to show the battery percentage; for example, if the keys from 1! to 6^ light up when holding Fn+Spacebar, it means that the battery life is currently 60%; if keys of 1!-0) light up, battery life is 100%.

INDICATOR LIGHT

Charging: Red light stays for 2 seconds then off
Charged: Green light stays for 2 seconds then off
Win-lock: When the Win key light up, the key is disabled

SPECS

REPLACING KEYCAPS AND SWITCHES

For a full guide on how to remove keycaps and switches scan the QR Code or type in your browser:
https://epomaker.com/blogs/guides/diy-guide-how-to-remove-and-replace-your-mechanical-keyboardswitches

Included Tools

Remove Switches

Mechanical Switch
Example of a switch as seen from top after you remove the keycap to prepare for switch removal.
The Switch Puller tool aligns Vertically to the Switch to unclip the plastic securing the switch to the plate.

1. Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
2. Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
3. Using firm but gentle force pull the switch away from the keyboard using a vertical motion.

Install Switches

1. Check that all the switch metallic pins are perfectly straight and clean.
   
2. Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
3. Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
   
4. Inspect the switch to ensure it's properly attached to your keyboard, and test it.

Note: If the key doesn't work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process.
Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid damage to the keyboard due to operating errors.

TECHNICAL ASSISTANCE

For technical assistance, please email to support@epomaker.com with your purchase order number and a detailed description of your issue.

We normally respond to enquiries within 24 hours. If you purchased your keyboard from a distributor or not from any official store of Epomaker, pelase contact them directly for any additional help.

COMMUNITY FORUMS

Join our community and learn together with other keyboard enthusiasts.

https://discord.gg/2q3Z7C2

https://www.reddit.com/r/Epomaker/

Manufacturer: Shenzhen Changyun Technology Co., Ltd.
Address: Seventh Floor, Kai Daer Building, No.168 Tongsha Road, Xili Street, Nanshan Disctrict, Shenzhen, Guangdong, CN
Email: support@epomaker.com
Web: www.epomaker.com

Documents / Resources

References

• Epomaker
• Reddit - Dive into anything
• http://www.epomaker.com

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download EPOMAKER EP75 - Hot-Swap Wired/Wireless Mechanical Keyboard Quick Manual