Page 1
WhatsApp community↑ D8L222HS03 D8L222BS03 As this item contains many parts, please read the installation instruction carefully before installation . Please use tools properly and carefully. If you have any questions about the product and installation, please contact us. service@vabchesofficial.com Our professional after-sales team will serve you online all day.
Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer Caution: If using a power drill or power screwdriver for screwing, please be aware of to slow down and stop when screw is tight.
Board Identification Not actual size LEFT SIDE PANEL RIGHT SIDE PANEL Qty:1 Qty:1 Qty:1 BACK BOARD BACK BOARD FRONT SLAT PANEL Qty:1 Qty:1 Qty:1 DRESSING MIRROR UPPER SIDE PANEL FRAME TOP BOARD Qty:1 Qty:2 Qty:1 DRAWER FRONT DRAWER LEFT PANEL DRAWER RIGHT PANEL Qty:1 Qty:1...
Page 4
Board Identification Not actual size DRAWER BACK PANEL DRAWER BOTTOM DRAWER MIDDLE PARTITION Qty:1 Qty:1 Qty:1 DRAWER SUPPORT RAIL STOOL BACK APRON STOOL SIDE PANEL Qty:1 Qty:1 Qty:2 STOOL FRONT APRON STOOL BOTTOM BOARD SPONGE CUSHION Qty:1 Qty:1 Qty:1 4-24...
Page 5
Board Identification Not actual size 5-24...
Part List Ø15X11mm Ø15X9.5mm Ø6.5X35mm Ø8X40mm CAM LOCK CAM LOCK CAM BOLT WOOD DOWEL spare:2 spare:1 spare:2 spare:2 Ø6X30mm Ø3.5X14mm Ø4X35mm Ø6.3X50mm WOOD DOWEL SCREW SCREW SCREW spare:1 spare:1 spare:3 spare:2 14" M4X18mm 110*10*16mm 12CL X1 set SCREW LIGHT BULB HANDLE LEFT CABINET MEMBER spare:1...
Page 7
Part List Ø25mm X1set HINGE ANTI-TIPPING HARDWARE PLUG BOARD HAIR DRYER RACK Ø3X12mm Ø4X12mm SCREW SCREW spare:1 spare:1 Cam Lock Fastening System Insert the cam bolt into the hole first, then insert the cam lock and lock it. The opening must point toward the edge of the board 7-24...
Page 19
STEP12 X1 set Pass the bulb wire through the pre punched plate, then gently press the bulb and make it adhere to the plate. Tear off a layer of 3M polyethylene foam. 19-24...
Page 20
STEP13 1.Pass the bulb wire through the pre punched plate, then gently press the bulb and make it adhere to the plate, and then connect the adjacent bulbs successively through the wire head slot on the opposite side (corresponding to the line of the same color). 2.You can use the switch to turn on or off the light when you are putting on makeup, long press the switch to adjust the brightness of the light.
Page 23
STEP16 To adjust the vertical height. Loosen the four screws "A" on both hinges. Two of them are usually in slotted holes which allows you to adjust up or down by a few mm. Then tighten back up. To adjust depth. Loosen screw "B"...
Page 24
STEP17 NOTE :The tipping restraint hardware included is for wooden stud wall construction. It must be attached to a wall stud. Depending upon your wall construction different We have included a set of tipping restraint hardware for anchor hardware maybe required. Please contact your local this unit.