Advertisement
Quick Links
D3M545HS05
D3M545BS05
As this item contains many parts, please read the installation
instruction carefully before installation . Please use tools
properly and carefully. If you have any questions about the
product and installation, please contact us.
service@vabchesofficial.com
Our professional after-sales team will serve you online all
day.
1-32
Advertisement
Related Manuals for VABCHES D3M545HS05
Summary of Contents for VABCHES D3M545HS05
- Page 1 D3M545HS05 D3M545BS05 As this item contains many parts, please read the installation instruction carefully before installation . Please use tools properly and carefully. If you have any questions about the product and installation, please contact us. service@vabchesofficial.com Our professional after-sales team will serve you online all day.
-
Page 2: Before You Start
Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer Caution: If using a power drill or power screwdriver for screwing, please be aware of to slow down and stop when screw is tight. -
Page 3: Board Identification
Board Identification Not actual size DESK TOP LEFT SIDE PANEL RIGHT SIDE PANEL Qty:1 Qty:1 Qty:1 PARTITION FRONT SLAT REAR PANEL Qty:1 Qty:1 Qty:1 BACK SLAT UPPER LEFT SIDE PANEL UPPER RIGHT SIDE PANEL Qty:1 Qty:1 Qty:1 UPPER LEFT BACK PANEL UPPER RIGHT BACK PANEL DRESSING MIRROR Qty:1... - Page 4 Board Identification Not actual size FIXED SHELF LEFT DRAWER FRONT RIGHT DRAWER FRONT Qty:4 Qty:1 Qty:1 DRAWER LEFT PANEL DRAWER RIGHT PANEL DRAWER BACK PANEL Qty:2 Qty:2 Qty:2 DRAWER BOTTOM STOOL SIDE PANEL STOOL UPPER CROSSBEAM Qty:2 Qty:2 Qty:2 LOWER BEAM OF STOOL SPONGE CUSHION Qty:1 Qty:1...
-
Page 5: Part List
Part List Ø15X9.5mm Ø6.5X35mm Ø8X30mm Ø6X30mm CAM LOCK CAM BOLT WOODEN DOWEL WOODEN DOWEL spare:2 spare:2 spare:2 spare:2 Ø6.3X50mm Ø4X40mm Ø3.5X14mm M6X20mm SCREW SCREW SCREW BOLT spare:2 spare:3 spare:3 spare:1 12'' Ø4X14mm M4X15mm 102*8*16mm 300mm 12CL HANDLE SCREW BOLT LEFT CABINET MEMBER spare:1 spare:1 12''... - Page 6 Part List Ø35mm X1 set X1 set LIGHT BULB ANTI-TIPPING HARDWARE GROMMET Cam Lock Fastening System Insert the cam bolt into the hole first, then insert the cam lock and lock it. The opening must point toward the edge of the board 6-32...
- Page 7 Board Identification Not actual size 7-32...
- Page 8 STEP1 Ø4X40mm 8-32...
- Page 9 STEP2 Ø15X9.5mm Ø6.5X35mm Proper orientation of CAM LOCK 9-32...
- Page 10 STEP3 12'' 12'' Ø3.5X14mm 300mm 300mm 12DL 12DR 12DR 12DL N & O 10-32...
- Page 11 STEP4 Ø8X30mm Ø3.5X14mm 20X20X15mm 11-32...
- Page 12 STEP5 Ø6.3X50mm Ø3.5X14mm Ø21mm 4X65mm FLIP OVER 12-32...
- Page 13 STEP6 Ø6X30mm M x 4 13-32...
- Page 14 STEP7 Ø4X40mm Ø21mm 14-32...
- Page 15 STEP8 Ø4X40mm Ø21mm 15-32...
- Page 16 STEP9 Ø3.5X14mm Ø6.5X35mm FLIP OVER 16-32...
- Page 17 STEP10 Ø4X40mm 17-32...
- Page 18 STEP11 12" 12" Ø3.5X14mm 300mm 300mm 12CL 12CR 12CL 12CR 18-32...
- Page 19 STEP12 12" 12" Ø3.5X14mm 300mm 300mm 12CL 12CR 12CL FLIP OVER 12CR 19-32...
- Page 20 STEP13 Ø8X30mm 20-32...
- Page 21 STEP14 Ø8X30mm 21-32...
- Page 22 STEP15 Ø4X40mm 22-32...
- Page 23 STEP16 Ø6.3X50mm 4X65mm Ø21mm THIS STEP REQUIRES 2 PEOPLE 23-32...
- Page 24 STEP17 Ø15X9.5mm THIS STEP REQUIRES 2 PEOPLE Proper orientation of CAM LOCK 24-32...
- Page 25 STEP18 M6X20mm Ø4X14mm 4X65mm THIS STEP REQUIRES 2 PEOPLE Please tighten the screws to 80% first, and tighten all screws 100% after all parts are assembled. You can install the hair dryer rack(15) on the left or right according to your needs 25-32...
- Page 26 STEP19 Ø3.5X14mm X1 set 26-32...
- Page 27 STEP20 M4X15mm 102X8X16mm Ø35mm Cabinet Slide Drawer Slide 27-32...
- Page 28 STEP21 1.Pass the bulb wire through the pre punched plate, then gently press the bulb and make it adhere to the plate. X1 set Tear off a layer of 3M polyethylene foam. 28-32...
- Page 29 STEP22 Pass the three connectors through the grommet. X1 set 29-32...
- Page 30 STEP23 connect the adjacent bulbs successively through the wire head slot on the opposite side . Connect the lights according to the figure. First connect the switch with the first bulb, and then connect other bulbs in series. 30-32...
- Page 31 STEP24 When making up, you can use the switch to turn on or off the light. The dressing table brings you 3 color temperature light modes,touch the button you can easy light up the mirror and change colors to meet your different needs, long press to adjust the brightness.
- Page 32 STEP25 We have included a set of tipping restraint hardware for NOTE this unit. You must install this hardware to prevent :The tipping restraint hardware included is for accidents or injuries that can result from the unit falling. wooden stud wall construction. It must be attached to a When properly installed, this restraint can provide wall stud.