Page 1
D3M545BS0M D3M545HS0M As this item contains many parts, please read the installation instruction carefully before installation and complete the installation with the cooperation of your partner. Please use tools properly and carefully. If you have any questions about the product and installation, please contact us.
Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer Caution: If using a power drill or power screwdriver for screwing, please be aware of to slow down and stop when screw is tight.
Board Identification Not actual size LEFT SIDE PANEL RIGHT SIDE PANEL Qty:1 Qty:1 Qty:1 PARTITION UPPER LEFT SIDE PANEL UPPER RIGHT SIDE PANEL Qty:1 Qty:1 Qty:1 UPPER LEFT BACK PANEL UPPER RIGHT BACK PANEL DRESSING MIRROR Qty:1 Qty:1 Qty:1 3-32...
Page 4
Board Identification Not actual size FIXED SHELF FRONT SLAT BACK SLAT Qty:4 Qty:1 Qty:1 LEFT DRAWER FRONT RIGHT DRAWER FRONT DRAWER LEFT PANEL Qty:1 Qty:1 Qty:2 DRAWER RIGHT PANEL DRAWER BACK PANEL DRAWER BOTTOM Qty:2 Qty:2 Qty:2 4-32...
Page 5
Board Identification Not actual size LOWER FRAME RAIL RAIL Qty:2 Qty:1 Qty:1 RAIL SIDE FRAME OF STOOL RAIL Qty:1 Qty:2 Qty:2 RAIL RAIL SPONGE CUSHION Qty:2 Qty:1 Qty:1 5-32...
Page 6
Board Identification Not actual size BACK PANEL Qty:1 6-32...
Page 7
Board Identification Not actual size 7-32...
Page 9
Part List SCREW:Ø3.5*14 4X65mm Ø21mm Ø48mm SCREW:Ø3.2*30 X1 set HEX KEY HOLE STICKER LIGHT BULB TIPPING RESTRAINT spare:2 HARDWARE KIT GROMMET Cam Lock Fastening System Insert the cam bolt into the hole first, then insert the cam lock and lock it. The opening must point toward the edge of the board 9-32...
Page 19
STEP10 M6X40mm M6X12mm Before you install this screw, please make sure the screw size is M6*40mm M6*40mm M6*12mm Before you install this screw, please make sure the screw size is M6*12mm 19-32...
Page 20
STEP11 M6X40mm M6X12mm Before you install this screw, please make sure the screw size is M6*40mm M6*40mm ROTATE Before you install this screw, please make sure the screw size is M6*12mm M6*12mm 20-32...
Page 21
STEP12 Ø15X9.5mm Proper orientation of CAM LOCK 21-32...
Page 22
STEP13 M6X20mm Before you install this screw, please make sure the screw size is M6*20mm M6*20mm 22-32...
Page 23
STEP14 SCREW:Ø3.5*14 Ø3X14mm X1 set 90° Before attaching the back panel, be sure that the unit is at 90°. Avant de fixer le panneau arrière, assurez-vous que l'unité est à 90°. 23-32...
Page 28
STEP19 M6X35mm M6X12mm Before you install this screw, please make sure the screw size is M6*35mm M6*35mm M6*12mm Before you install this screw, please make sure the screw size is M6*12mm Before you install this screw, please make sure the screw size is M6*35mm M6*35mm 28-32...
Page 29
STEP20 Ø48mm 1.Pass the bulb wire through the pre punched plate, then gently press the bulb and make it adhere to the plate. Tear off a layer of 3M polyethylene foam. 29-32...
Page 30
STEP21 connect the adjacent bulbs successively through the wire head slot on the opposite side . Connect the lights according to the figure. First connect the switch with the first bulb, and then connect other bulbs in series. 30-32...
Page 31
STEP22 When making up, you can use the switch to turn on or off the light. The dressing table brings you 3 color temperature light modes,touch the button you can easy light up the mirror and change colors to meet your different needs, long press to adjust the brightness.
Page 32
STEP23 NOTE :The tipping restraint hardware included is for wooden stud wall construction. It must be attached to a wall stud. Depending upon your wall construction different SCREW : Ø3.2*30 We have included a set of tipping restraint hardware for anchor hardware maybe required.