GREE ELECTRIC GWH07AGA-K6DNA1A/O Service Manual page 55

● Maximum power limited under the
mode.
● If the current power is lower than the maximum power of
mode, then the power will not be limited after entering into such
mode.
● For the model with one outdoor unit and two indoor units, if any
one of indoor units enters into power limiting function, the outdoor
unit will enter into the set limiting power mode of indoor unit; when
two indoor units enter into power limiting mode, then the power of
outdoor unit will be limited according to the lower power of the two
indoor units.
NOTE:
● The function is only available for some models.
6. SWING button
Press this button can select up & down swing angle. Fan blow
angle can be selected circularly as below:
no display
(horizontal louvers stops
at current position)
● When selecting "
automatically. Horizontal louver will automatically swing up &
down at maximum angle.
● When selecting " ,
fan at fixed position. Horizontal louver will stop at the fixed
position.
● Hold " " button above 2s to set your required swing angle.
When reaching your required angle, release the button.
NOTE:
● Press this button continuously for more than 2s, the main
unit will swing back and forth from up to down, and then loosen
the button, the unit present position of guide louver will be kept
immediately.
● Under up and down swing mode, when the status is switched
from off to , if press this button again 2s later,
switch to off status directly; if press this button again within 2s,
the change of swing status will also depend on the circulation
sequence stated above.
7. TURBO button
Under COOL or HEAT mode, press this button to turn to quick
COOL or quick HEAT mode. "
controller. Press this button again to exit turbo function and "
icon will disappear. If start this function, the unit will run at super-high
fan speed to cool or heat quickly so that the ambient temperature
approaches the preset temperature as soon as possible.
Function introduction for combination buttons
52
mode is lower than that of
", air conditioner is blowing fan
, , , ", air conditioner is blowing
status will
" icon is displayed on remote
1. Child lock function
Press "+" and "-" simultaneously to turn on or turn off child lock
function. When child lock function is on, "
remote controller. If you operate the remote controller, the "
icon will blink three times without sending signal to the unit.
2. Temperature display switchover function
Under OFF status, press "-" and "MODE" buttons simultaneously
to switch temperature display between °C and °F.
3. Auto clean function
Under unit off status, hold "MODE" and "FAN" buttons
simultaneously for 5s to turn on or turn off the auto clean function.
When the auto clean function is turned on, indoor unit displays
"CL". During the auto clean process of evaporator, the unit will
perform fast cooling or fast heating. There may be some noise,
which is the sound of flowing liquid or thermal expansion or cold
shrinkage. The air conditioner may blow cool or warm air, which
is a normal phenomenon. During cleaning process, please make
sure the room is well ventilated to avoid affecting the comfort.
NOTE:
● The auto clean function can only work under normal ambient
temperature. If the room is dusty, clean it once a month; if not,
clean it once every three months. After the auto clean function is
turned on, you can leave the room. When auto clean is finished,
the air conditioner will enter standby status.
● This function is only available for some models.
4. WiFi function
Press "MODE" and "TURBO" button simultaneously to turn on or
turn off WiFi function. When WiFi function is turned on, the "WiFi"
icon will be displayed on remote controller; Long press "MODE"
and "TURBO" buttons simultaneously for 10s, remote controller
will send WiFi reset code and then the WiFi function will be turned
on. WiFi function is defaulted ON after energization of the remote
controller.
NOTE:
● The function is only available for some models.
5. Ambient temperature display function
Press "SWING" and "SET" buttons simultaneously, you can see
indoor ambient temperature on indoor unit's displayer and the
" icon will be displayed on remote controller. The setting on
remote controller is selected circularly as below:
"
6. Adjustable temperature under auto mode
The remote controller defaulted that the set temperature can't
" icon is displayed on
no display
Technical Information
Service Manual
"
"