GREE ELECTRIC GWH07AGA-K6DNA1A/O Service Manual page 49

position.
● When selecting " ,
fixed angle. Horizontal louver will send air at the fixed angle.
● Hold " " button above 2s to set your required swing angle.
When reaching your required angle, release the button.
NOTE:
● " , , " may not be available. When air conditioner
receives this signal, the air conditioner will blow fan
automatically.
● Press this button continuously for more than 2s, the main
unit will swing back and forth from up to down, and then loosen
the button, the unit present position of guide louver will be kept
immediately.
● Under up and down swing mode, when the status is switched
from off to , if press this button again 2s later,
switch to off status directly; if press this button again within 2s,
the change of swing status will also depend on the circulation
sequence stated above.
button
T-ON T-OFF
● T-ON button
"T-ON" button can set the time for timer on. After pressing this
button, " " icon disappears and the word "ON" on remote
controller blinks. Press "
After each pressing " " or "
or decrease 1min. Hold "
change quickly until reaching your required time. Press "T-ON"
to confirm it. The word "ON" will stop blinking. "
displaying. Cancel T-ON: Under the condition that T-ON is started
up, press "T-ON " button to cancel it.
● T-OFF button
"T-OFF" button can set the time for timer off. After pressing this
button, " " icon disappears and the word "OFF" on remote
controller blinks. Press "
setting. After each pressing "
will increase or decrease 1min. Hold "
the time will change quickly until reaching your required time.
Press "T-OFF" word "OFF" will stop blinking. "
displaying. Cancel T-OFF. Under the condition that T-OFF is
started up, press "T-OFF" button to cancel it.
NOTE:
● Under on and off status, you can set T-OFF or T-ON simultaneously.
● Before setting T-ON or T-OFF, please adjust the clock time.
● After starting up T-ON or T-OFF, set the constant circulating
valid.
46
, ", air conditioner is blowing fan at
status will
" or " " button to adjust T-ON setting.
" button, T-ON setting will increase
" or " " button, 2s later, the time will
" icon resumes
" or " " button to adjust T-OFF
" or " " button, T-OFF setting
" or " " button, 2s later,
" icon resumes
● After that, air conditioner will be turned on or turned off
according to setting time. ON/OFF button has no effect on setting.
If you don't need this function, please use remote controller to
cancel it.
button
I FEEL
Press this button to start I FEEL function and "
on the remote controller. After this function is set, the remote
controller will send the detected ambient temperature to the controller
and the unit will automatically adjust the indoor temperature
according to the detected temperature. Press this button again to
cancel I FEEL function and "
● Please put the remote controller near user when this function
is set. Do not put the remote contro ller near the object of high
temperature or low temperature in order to avoid detecting
inaccurate amb ient temperature. When I FEEL function is turned
on, the remote controller should be put within the area where
indoor unit can receive the signal sent by the remote controller.
button
CLOCK
Press this button to set clock time. "
will blink. Press " " or "
Each pressing of " " or "
decrease 1 minute. If hold "
change quickly. Release this button when reaching your required
time. Press "CLOCK" button to confirm the time. "
blinking.
NOTE:
● Clock time adopts 24-hour mode.
● The interval between two operations can't exceed 5s.
Otherwise, remote controller will quit setting status. Operation for
TIMER ON/TIMER OFF is the same.
button
SLEEP
● Press this button, can select Sleep 1 (
Sleep 3 ( 3) and cancel the Sleep, circulate between these, after
electrified, Sleep Cancel is defaulted.
● Sleep 1 is Sleep mode 1, in Cool modes; sleep status after run
for one hour, the main unit setting temperature will increase 1 ,
two hours, setting temperature increased 2°C, then the unit will
run at this setting temperature; In Heat mode: sleep status after
run for one hour, the setting temperature will decrease 1 , two
hours, setting temperature will decrease 2 , then the unit will run
at this setting temperature.
● Sleep 2 is sleep mode 2, that is air conditioner will run according
to the presetting a group of sleep temperature curve.
● Sleep 3- the sleep curve setting under Sleep mode by DIY;
Service Manual
" will be displayed
" will disappear.
" icon on remote controller
" button within 5s to set clock time.
" button, clock time will increase or
" or " " button, 2s later, time will
" icon stops
1), Sleep 2 (
Technical Information
2),