GREE ELECTRIC GWH07AGA-K6DNA1A/O Service Manual page 50

Service Manual
(1) Under Sleep 3 mode, press "Turbo" button for a long time,
remote controller enters into user individuation sleep setting
status, at this time, the time of remote controller will display "1hour",
the setting temperature "88" will display the corresponding
temperature of last setting sleep curve and blink (The first entering
will display according to the initial curve setting value of original
factory);
(2) Adjust " " and " " button, could change the corresponding
setting temperature, after adjusted, press "Turbo" button for
confirmation;
(3) At this time, 1hour will be automatically increased at the timer
position on the remote control, (that are "2hours" or "3hours" or
"8hours"), the place of setting temperature "88" will display the
corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 hours
temperature setting finished, sleep, curve setting finished, at this
time, the remote controller will resume the original timer display;
temperature display will resume to original setting temperature.
● Sleep3- the sleep curve setting under Sleep mode by DIY could
be inquired:
The user could accord to sleep curve setting method to inquire the
presetting sleep curve, enter into user individuation sleep setting
status, but do not change the temperature, press "Turbo" button
directly for confirmation.
NOTE: In the above presetting or enquiry procedure, if
continuously within 10s, there is no button pressed, the sleep
curve setting within 10s, there is no button pressed, the sleep
curve setting status will be automatically quit and resume to
display the original displaying. In the presetting or enquiry
procedure, press "ON/OFF" button, "MODE" button, "SLEEP"
button, the sleep curve setting or enquiry status will quit similarly.
button
WiFi
Press " WiFi " button to turn on WiFi function, " WiFi " icon will be
displayed on the remote controller; Hold " WiFi " button for 5s to
turn off WiFi function and " WiFi " icon will disappear.
Under off status, press " MODE " and " WiFi " buttons simultaneously
for 1s, WiFi module will restore factory settings.
● This function is only available for some models.
button
Press this button to achieve the on and off of health and
scavenging functions in operation station. Press this button for the
first time to start scavenging function; LCD displays " ". Press
the button for the second time to start health and scavenging
functions simultaneously; LCD displays " " and " ". Press this
button for the third time to quit health and scavenging functions
simultaneously. Press the button for the fourth time to start health
Technical Information
function; LCD display " ". Press this button again to repeat the
operation above.
● This function is applicable to partial of models.
button
LIGHT
Press this button to turn off display light on indoor unit. "
on remote controller disappears. Press this button again to turn on
display light. " " icon is displayed.
button
TEMP
Press this button, you can see indoor set temperature, indoor
ambient temperature on indoor unit's display. The setting on
remote controller is selected circularly as below:
no display
Function introduction for combination buttons
Energy-saving function
Under cooling mode, press "TEMP" and "CLOCK" buttons
simultaneously to start up or turn off energysaving function. When
energy-saving function is started up, "SE" will be shown on remote
controller, and air conditioner will adjust the set temperature
automatically according to ex-factory setting to reach to the
best energy-saving effect. Press "TEMP" and "CLOCK" buttons
simultaneously again to exit energysaving function.
NOTE:
● Under energy-saving function, fan speed is defaulted at auto
speed and it can't be adjusted.
● Under energy-saving function, set temperature can't be
adjusted. Press "TURBO" button and the remote controller won't
send signal.
● Sleep function and energy-saving function can't operate at the
same time. If energy-saving function has been set under cool
mode, press sleep button will cancel energy-saving function.
If sleep function has been set under cool mode, start up the
energy-saving function will cancel sleep function.
8°C heating function
Under heat mode, press "TEMP" and "CLOCK" buttons
simultaneously to start up or turn off 8°C heating function. When
this function is started up, " " and "8°C" will be shown on remote
controller, and the air conditioner keep the heating status at 8°C.
Press "TEMP" and "CLOCK" buttons simultaneously again to exit
8°C heating function.
NOTE:
● Under 8°C heating function, fan speed is defaulted at auto
speed and it can't be adjusted.
" icon
47