GREE ELECTRIC GWH07AGA-K6DNA1A/O Service Manual page 53

indoor ambient temperature).
● Set temperature range from remote controller: 16~30°C(61~86°F).
● This mode indicator is not available for some models.
● Cooling only unit won't receive heat mode signal. If setting heat
mode with remote cont roller, press "
unit.
3. Fan button
This button is used for setting Fan Speed in the sequence that
goes from AUTO, ,
Auto.
NOTE:
● Under AUTO speed, air conditioner will select proper fan speed
automatically according to factory default setting.
● It's low fan speed under dry mode.
● X-FAN function: Holding fan speed button for 2s in cool or dry
mode, the icon " " is displayed and the indoor fan will continue
operation for a few minutes in order to dry the indoor unit even
though you have turned off the unit. After energization, X-FAN
OFF is defaulted. X-FAN is not available in auto, fan or heat
mode.
This function indicates that moisture on evaporator of indoor unit
will be blowed after the unit i s stopped to avoid mould.
● Having set X-FAN function on: After turning off the unit by
pressing " " button, indoor fan will continue running for a few
minutes at low speed. In this period, hold fan speed button for 2s
to stop indoor fan directly. Having set X-FAN function off: After
turning off the unit by pressing "
be off directly.
4. - / + button
Press "+" or "-" button once increase or decrease set temperature
1°C(°F). Holding "+" or "-" button, 2s later, set temperature on
remote controller will change quickly. On releasing button after
setting is finished, temperature indicator on indoor unit will change
accordingly. (Temperature can' t be adjusted under auto mode)
When setting TIMER ON, TIMER OFF or CLOCK, press "+" or "-"
button to adjust time. (Refer to CLOCK, TIMER ON, TIMER OFF
functions).
5. MENU button
Press this button to select submenu function and then press
"SET" button to set the function status of submenu. The submenu
can be selected circularly as follows:
blank
No Setting
50
" button can't start up the
, , , , , then back to
" button, the complete unit will
TIMER TIMER
ON OFF
/
NOTE:
Some menu's function may be unavailable under different models.
Light function
When selecting light function, light icon "
"SET" button within 5s to turn off display light on indoor unit and
" " icon on remote controller disappears. Press "SET" button
again within 5s to turn on display light and "
Sleep function
When selecting sleeping function, sleeping icon "
5s; press "SET" button within 5s can select Sleep 1 (
2), Sleep 3 ( 3) and cancel Sleep circularly.
● Sleep 1 is Sleep mode 1, in Cool modes; sleep status after run
for one hour, the main unit setting temperature will increase 1°C,
two hours, setting temperature increased 2°C, then the unit will
run at this setting temperature; In Heat mode: sleep status after
run for one hour, the setting temperature will decrease 1°C, two
hours, setting temperature will decrease 2°C, then the unit will run
at this setting temperature.
● Sleep 2 is sleep mode 2, that is air conditioner will run according
to the presetting a group of sleep temperature curve.
● Sleep 3-the sleep curve setting under Sleep mode by DIY;
(1) Under Sleep 3 mode, press "Turbo" button for a long time,
remote controller enters into user individuation sleep setting
status, at this time, the time of remote controller will display "1hour",
the setting temperature "88" will display the corresponding
temperature of last setting sleep curve and blink (The first entering
will display according to the initial curve setting value of original
factory);
(2) Adjust "+" and "-" button, could change the corresponding
setting temperature, after adjusted, press "Turbo" button for
confirmation;
(3) At this time, 1hour will be automatically increased at the timer
position on the remote control, (that are "2hours" or "3hours" or
"8hours"), the place of setting temperature "88" will display the
corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 hours
temperature setting finished, sleep,curve setting finished, at this
time, the remote controller will resume the original timer display;
temperature display will resume to original setting temperature.
● Sleep3- the sleep curve setting under Sleep mode by DIY could
be inquired:
The user could accord to sleep curve setting method to inquire the
presetting sleep curve, enter into user individuation sleep setting
status, but do not change the temperature, press "Turbo" button
directly for confirmation. Note: In the above presetting or enquiry
Service Manual
" flashes for 5s; press
" icon is displayed.
" flashes for
1), Sleep 2 (
Technical Information