GREE ELECTRIC GWH07AGA-K6DNA1A/O Service Manual page 54

Service Manual
procedure, if continuously within 10s, there is no button pressed,
the sleep curve setting within 10s, there is no button pressed, the
sleep curve setting status will be automatically quit and resume
to display the original displaying. In the presetting or enquiry
procedure, press " " button, "MODE" button, the sleep curve
setting or enquiry status will quit similarly.
TIMER ON function
TIMER ON function can set the time for timer on. Under TIMER
ON function status, " " icon disappears and the word "ON" on
remote controller blinks. Press "+" or "-" button to adjust TIMER
ON setting. After each pressing "+" or "-" button, TIMER ON
setting will increase or decrease 1min. Hold "+" or "-" button, 2s
later, the time will change quickly until reaching your required
time. Press "SET" button to confirm it within 5S. The word "ON"
will stop blinking.
Cancel TIMER ON: Press "MENU" button to TIMER ON function
and the characters "ON" flashes on the remote controller; press
"SET" button until the characters "ON" disappears.
TIMER OFF function
TIMER OFF function can set the time for timer off. Under TIMER
OFF function status, " " icon disappears and the word "OFF" on
remote controller blinks. Press "+" or "-" button to adjust TIMER
OFF setting. After each pressing "+" or "-" button, TIMER OFF
setting will increase or decrease 1min. Hold "+" or "-" button, 2s
later, the time will change quickly until reaching your required
time, press "SET" button to confirm it within 5S. The word "OFF"
will stop blinking.
Cancel TIMER OFF: Press "MENU" button to TIMER OFF function
and the characters "OFF" flashes on the remote controller; press
"SET" button until the characters "OFF" disappears.
CLOCK function
CLOCK function can set clock time. Under CLOCK function status,
" " icon on remote controller will blink. Press "+" or "-" button
within 5s to set clock time. Each pressing of "+" or "-" button, clock
time will increas e or decrease 1 min. If hold "+" or "-" button, 2s
later, time will change quickly. Release this button when reaching
your required time, press "SET" button to confirm it within 5S. The
" " icon will stop blinking.
Left & right swing function
When selecting left & right swing function, left & right swing icon
" " flashes for 5s; press "SET" button within 5s to select left &
right swing angle.
Fan blow angle can be selected circularly as below:
Technical Information
no display
(stops at current
position)
NOTE:
● The function is only available for some models.
I FEEL function
When selecting I FEEL function, I FEEL icon "
Press "SET" button to start I FEEL function within 5s and "
be displayed on the remote controller. After this function is set,
the remote controller will send the detected ambient temperature
to the controller and the unit will automatically adjust the indoor
temperature according to the detected temperature. Press "SET"
button again to cancel I FEEL function and "
Please put the remote controller near user when this function
is set. Do not put the remote controller near the object of high
temperature or low temperature in order to avoid detecting
inaccurate ambient temperature.When I FEEL function is turned
on, the remote controller should be put within the area where
indoor unit can receive the signal sent by the remote controller.
Energy-saving function
Under cooling mode, when selecting energy-saving function,
energy-saving function icon "
button within 5s to turn on or turn off energy-saving function.
When energy-saving function is started up, "SE" will be shown
on remote controller, and air conditioner will adjust the set
temperature automatically according to ex-factory setting to reach
to the best energy-saving effect. Press "SET" button again to exit
energy-saving function.
8°C-heating function
Under heating mode, when selecting 8°C-heating function,
8°C-heating icon " " flashes for 5s; press "SET" button within 5s
to turn on or turn off 8°C-heating. When 8°C-heating is started up,
" " will be shown on remote controller, and the air conditioner
keep the heating status at 8°C. Press "SET" button again to exit
8°C-heating function.
NOTE:
● Under °F temperature display, the remote controller will display
46°F heating.
Power limiting function
Power limiting function is for limiting the power of the whole
unit. When selecting power limiting function, power limiting icon
" " flashes for 5s; press "SET" button within 5s and the remote
controller will circularly display as follows:
" flashes for 5s.
" will
" will disappear.
" flashes for 5s; press "SET"
blank
No Setting
51