Summary of Contents for DREAMS DAWSON OTTOMAN SOUND BED with O.S.B.
Page 1
DAWSON OTTOMAN SOUND BED with O.S.B. SINGLE SIZE IMPORTANT OTTOMAN SAFETY WARNINGS IMPORTANT – READ CAREFULLY – RETAIN FOR FUTURE REFERENCE You must ensure that the mattress is on the bed frame before operating the lift mechanism – Failure to do so could result in injury. Keep hands clear of the mechanism when opening or closing the ottoman.
Page 2
IMPORTANT OTTOMAN SAFETY WARNINGS Cont. Ensure mattress is on before lifting Don’t lift without mattress • Use caution when operating, always use the handle when lifting. • Note: This bed uses a pressurised mechanism. • To be operated by adults only. •...
Page 3
Ottoman Beds - Important Safety Features your comfort and safety. Please take time to look at these instruction as they will help remind you how to operate your ottoman bed safely. Here’s a few things you need to remember; Pistons are already assembled in their correct orientation – this improves piston performance and durability.
Thank You Dear Customer, Thank you for choosing to purchase your bed from Dreams - we hope it brings you your best ever night’s sleep. Before you begin building your bed, please take a moment to read through the instructions and make sure that you've got all the relevant parts listed on the following pages.
Parts Important information The bed you have purchased comes with an Ottoman lift up base, please follow the instructions below in the current order. Before you begin building your bed, please take a moment to read through the instructions and make sure that you've got all the relevant parts listed on the following pages.
Fittings Please check you have all the parts listed below with your product: Hardware needed for fixing wings to headboard and assembling the bed Packed in headboard pack 3 - hardware pack (A) a x20 b x20 c x20 d x1 Bolts (M8x30mm) for fitting side rails (C&D) to headboard Spring washer for M8 bolts...
Page 7
Prepare the bed for assembly - use pack 'A' 10mm b x4 a x4 b x4 a x4 c x4 Fit the side rails (C & D). & Dawson Ottoman Sound Bed - Assembly guide - Page 7...
Page 8
Fit the two angled corner brackets (F). c x4 b x4 a x4 Fit the base board support rails (K). Make certain the K x4 bed is squared up 100% as shown in the diagram then tighten all bed assembly bolts 100%.
Page 9
Carefully fit the storage base boards (J). Fit the slat frame support rail (I) Fit slat frame support rail (I) to footboard using two bolts (j) & flat washers (c). Using Allen Key (d) tighten 100%. c x2 j x2 Dawson Ottoman Sound Bed - Assembly guide - Page 9...
Page 10
Prepare the metal slat frame (E). Fitting position for cross bar (G) is clearly labeled. Pass bar through metal slat frame between first & second slat. Carefully open the frame. Using four bolt sets (g, b & c) fit the two metal connection plates (h) screwing into the threaded inserts on top of the frame.
Page 11
Fit the metal slat-frame. Un-tie the hinge mechanism, and take out the transit block. & Hold bars forward Slat Frame Support Bar iii) With help from an assistant, lift slat frame (E) onto slat frame support bars aligning first set of holes on slat frame with first set of holes in the support bars (nearest to headboard).
Page 12
Align the slat frame. Carefully lay frame down making sure there is an even gap all round as in the sketch. Hold frame securely then tighten all six bolt sets 100% using spanner (f) & allen key (d). Fit the gas-lift piston stems to the lower axles. During this next step, the assistant should hold up the slat frame.
Page 13
Push the mattress Fit the mattress stopper (H). stopper (H) into the end of the metal slat frame, the legs should go all the way through the upper & lower metal sections. Unpack the contents of the Ottoman Support Bar (O.S.B.) from it's carton - this is packed inside Pack 3.
Page 14
Setting the inner stem of the support bar (M), adjust the inner stem to the correct length. Parking position Set the inner stem to the correct length so the end just touches the retaining bracket - it needs to touch to hold it in position. 100% Adjust the retaining bracket (N) so the stem end scrapes the surface.
Electrical Connection for Stereo System Note that the power supply to the 2.0 stereo system is a maximum of 5 Volts - for safety, only use the power supply supplied with the bed. Connect the LV connector on the power lead (L) to the connector (X) underneath the headboard.
Technical Specifications Overall Dimensions (LWH cm) 211.5 x 104 x 113 Internal Dimensions (LWH cm) 193 x 92 x 24.5 Distance between slats (cm) Ottoman Piston Rating 600N Slat Dimensions (LWH cm) 45 x 5.3 x 0.9 37.5 Floor to top of slat Top of slat to top of side rail...
Page 17
Little dreamers Keep the little ones entertained while you assemble your new purchase.
Need help?
Do you have a question about the DAWSON OTTOMAN SOUND BED with O.S.B. and is the answer not in the manual?
Questions and answers