DREAMS DONNIE Manual

Bedstead

Advertisement

Quick Links

IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - P LEASE READ THESE INSTRUCTIONS CAREFULLY

Parts Identification

1
3

Parts Checklist

Ref.
Description
1
Headboard
2
Footboard
3
Side Panels
4
Wooden Slat Set
5
Wooden Slat Set Support Leg
170628
DONNIE BEDSTEAD
PLEASE READ this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in
a safe environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be
e k
t p
the danger of choking.
3
2
Qty
Ref. Description
1
6
1
7
2
8
1
*
1
Page 1 of 5
a
w
a
f y
o r
m
o y
u
n
g
h c
d l i
e r
n
Note:
Standard wooden slat set (part 4)
Upgraded sprung slat frame (part 6)
*Upgraded Sprung Slat Frame*
*Sprung Slat Frame Centre Support Leg*
S *
p
u r
n
g
S
t a l
F
a r
m
e
S
u
p
Only supplied if upgraded sprung slat frame is chosen.
Legs (7&8) are only supplied with the sprung system.
d
r u
n i
g
s a
e s
m
b
, y l
o t
a
o v
d i
4
5
6
7
8
Qty
1
1
p
o
t r
L
e
g
* s
2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DONNIE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for DREAMS DONNIE

  • Page 1 DONNIE BEDSTEAD PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction. Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
  • Page 2 Fittings Checklist HARDWARE NEEDED FOR BED ASSEMBLY (PACK A) Code Description Code Description Bolts (M8x30mm) for Flat Washers (for M8 bolt) fitting side panels (3) to headboard & footboard (1&2). Spring Washers (for M8 bolt) Allen Key (for M8 bolt) HARDWARE FOR FITTING WOOD SLATS OR UPGRADED SPRUNG SLAT FRAME (PACK B) Code Description...
  • Page 3 Stage Loosely insert four bolts (A) with spring washers (B) & flat washers (C) into each side of headboard & footboard (1&2). 10mm Note: Do not tighten fully but leave 10mm protruding as in the diagram MAKE CERTAIN THE BED IS SQUARED UP, AS SHOWN IN THE DIAGRAM.
  • Page 4 Fitting Wooden Slats - Use Pack 'B' Stage Carefully lay wooden slat set (4) on the metal supports on each side panel. Using two bolts (E) with spring washers (V), flat washers (G) and sleeve nuts (F) fix one slat next to headboard.
  • Page 5 Fitting Upgraded Sprung Slat Frame - Use Pack 'B' Stage Open the sprung slat frame and lay face down on the working surface. Fit the support legs (7 & 8 ) to the positions shown, securing with the bolts (P). Fully tighten using Allen key (H). Carefully turn the slat frame over and position onto the metal slat supports on each side panel.

Table of Contents