Keithley 486 Instruction Manual page 231

I
I-Limit, 3-13
I-Limit (Model 487), 3-18
IBMPC/XT/ATorFS/2 with IO&h
Driver488 Software, D-6
IBM PC/XT/AT with Capital Equipment
Corporation PCcA88 Interface (Keithley
PC-488.CEC), D-2
IBM PC/XT/AT with CEC PC0488 Interface
and ASYST Software package, D-4
IMP PC/XT/AT with National GPIB PC
Interface, D-7
IDDC (Illegal Device-Dependent Command)
Erm, 4-48
IDDCO (Illegal Device-Dependent Command
Option), 4-49
IEEE Command Groups, E-7
IEEE-488 Address or Talk-Only, 3-18
IEEE488 BUS CONNECTIONS, 4-46
IEEE488 Bus Calibration, 7-b
IEEE-488 Bus Command Summary, E-4
IEEE-488 BUS Overview, E-l
IEEE 488 Interface, 6-13
IEEE488 OPERATION, 2-9
IEEE488 Status Indicators, 4-5"
IFC (Interface Clear), 4-44
Input Amplifier, 6-1
Input Connector, 3-8
Integration, 3-18
htegration Period, 4-30
Interface Function Codes. B-1
L
Leakage Resistance, 3-16
LINE FUSE REPLACEMENT, 7-1
Line Cycle Integration, 33
Line Voltage Setting, 3-1
LLO (Local Lockout), 4-45
LOCAL Key, 4-51
M
Machine Status Word, 4-32
MENU, 3-16
Memory Map, 6-11
Meter Cmplete, 3-23
Microcomputer, b-11
Model 4288-l Single Fixed Rack
Mount Kit, 1-3
Model 4288-2 Dual Fixed Rack Mount Kit, l-3
Model 486 Front Panel, 2-2
Model 486 Rear Panel, 2-4
Model 487 Front Panel, 2-3
Model 487 Rear Panel, 2-5
Model 6105 Resistivity Chamber, l-3
Model 61713.slot to 2-lug Triax Adapter, l-3
Model 7007 Shielded IEEE-488 Cables, l-3
Model 7078-TRX Triaxial Cables, 1-3
Model 8002A High Resistance Test Fixtuw l-3
Mode, 8006 Component Test Fixture, l-3
Model number and Firmware Revision, 4-35
Multiplexer, 6-3
Multiplexer Phases, b-5
N
No Remote Error, 4-49
0
Offset Voltage Adjust, 6-2
operate, 3-13
Operate (Model 487). 4-26
Optimizing Accuracy, 3-16
ORDERING INFORMATION, 8-1
P
PARTS LIST, 8-l
Performance Verification, 5-I
Picoammeter Verification 5-2
Piezoelechic Effects, 3-34
POWER S"PPLIES, 6-14
Power Cord, 3-2
Power Supplies, 6-6
Power up Sequence, 3-2
PRIMARY ADDRESS SELECTION, 4-47
Preset, 3-n
R
Radio Frequency Interference, 3-35
Range, 4-29
Range Relays, 6-2
REN (Remote Enable), 444
Reading Source, 4-7
Recalling Data, 3-25
Recommended Calibration Equipment, 7-1
Rel, 3-7
Relative, 4-42
Relative Value (Current), 4-36
Relative Value (V/I Ohms), 4-36
S
SCHEMATIC AND COMPONENT
LOCATION DRAWINGS, 8-l
SDC (Selective Device Clear), 4-45
Self-Test, 3-19
Self-Tests, 4-16
Source Capacitance, 3-33
Source Resistance, 3-33
WE, SPD (Serial Polling), 446
SPECIAL HANDLING OF STATIC
SENSI'IWE DEVICES, 7-U
SRQ Mask and Serial Pall Byte Format, 4-21
Status, 4-32
Storing Data at Progranm,ed Intervals, 3-23
T
TALK-ONLY, 3-27
Terminator, 441
Test Fixture and Interlock, 3-10
Thermal EMFs, 3-35
TROUBLESHOOTING, 7-12
Triboelectric Effects, 3-34
Trigger, 4-31
Trigger Delay. 3-21,4-35
Trigger Interval, 3-21,4-35
Trigger Mode, 3-20
Trigger Overrun Error, 449
Trigger Sources, 3-21
Triggering One-shot Reading into Data
store, 3-24