Digital Monitoring Products XF6 Series Installation And Programming Manual page 20

715-16 Zone Expander
716 Output Expander
Auxiliary Modules
860 Relay Output Module
865 Style W/X Notification
Module
867 LX-Bus Notification Circuit
Module
Pull Stations
850 Series Pull Stations
Smoke/Heat Detectors
2W-BLX Conventional Smoke
Detector
2WT-BLX Conventional Smoke/
Heat Detector
Miscellaneous Accessories
335 Intrusion Siren
370 Lightning Suppressor
861 Power Distribution Module
Wiring harnesses, cables, and
tampers
Monitoring Center Receivers
SCS-1R Network Enabled
Receiver
SCS-VR Virtual Receiver
DMP Wireless
1100X Receiver
1100XH High-Power Receiver
1100R Repeater
1103 Universal Transmitter,
External Contact
1164 Wireless Smoke Detector
with Synchronized Sounder
XF6 Series Installation and Programming Guide
Provides 16 powered zones (12 VDC) supporting two-wire smoke detectors or
other fire alarm initiating devices. Includes red 340 enclosure and EOL resistors.
Provides 4 programmable Form C (SPDT) relays and four open collector
annunciator outputs. Use the outputs for remote zone and system annunciation or
environmental control applications. Harness included.
Provides electrical isolation between the alarm panel and other systems or for
switching voltage to control various functions.
Provides Style W or X supervision for ground faults, opens, and shorts on
Provides one supervised Style W circuit for 12 VDC or 28 VDC notification devices.
The 867 connects to the LX-Bus and supervises Ground Fault, Open and Short
conditions on the notification circuit.
Single or dual action pull stations with gold-plated SPST contacts and terminal
A photoelectric detector that includes an addressable single point module for
connection to the LX-Bus of the XF6 Series panels.
A photoelectric detector that includes an addressable single point module with a
restorable, built-in fixed temperature thermal detector and is capable of sensing a
Offers dual tones, steady and warble, is load-tested to four hours, is indoor surface-
mounted and is made out of UV-resistant, high-impact ABS plastic. 105 dB.
Provides lightning supression for any DMP or other manufacturer's panel.
Provides multiple auxiliary power terminals and additional keypad and/or LX-Bus
connectors for a clean installation. Maximum current handling capacity of 8 amps
Network Enabled Receiver compatible with central station receivers that accept
Standard CID, DD or DMP Serial 3 messaging.
Software-only solution that runs on a server for network IP and cellular
Provides Two-Way, supervised communication using 900 MHz frequency hopping-
spread spectrum technology. 1100XE-W features 128-bit AES encryption.
Provides additional transmit and receive amplification for improved performance at
greater distance or harsh building environments. 1100XHE-W features 128-bit AES
Provides increased communication range. Up to eight repeaters can be installed on
a wireless system. This model includes the 376L power supply. 1100RE-W features
Includes an internal magnetic reed switch, an on board terminal block for external
contact wiring, and an end-of-line resistor. Features 128-bit AES encryption.
Causes sounders to initiate when any fire zone is tripped on the panel, which also
triggers any other wired strobes and strobe horns. The cadence is dictated by the
panel, synchronizing the alarm tones of all wired and wireless devices.
notification appliance circuits.
strip connections.
temperature higher than 135 °F.
on power and ground in terminals.
300 Four-wire Harness
303 Silence/Reset Push Button
305 Plug-in Output Relay
306 Tamper Harness
307-S Screw-On Tamper Switch
374 Surge Voltage Suppressor
3012 Clip-On Tamper Switch
381 Coax Extension Cable
431 Output Harness
communications.
encryption.
128-bit AES encryption.
Digital Monitoring Products
15