Alarm Silence ..............8 Sensor Reset ..............8 Security Command User’s Guide ........ i Outputs On Off .............. 9 for XR100FC/XR500FC Panels ........i Zone Status ..............10 Table of Contents ............i System Status ............... 11 Emergency Evacuation Plans ........iii System Test ..............
Page 4
Change User Profiles Browser ......... 23 Add User Codes Browser ..........23 Delete User Codes Browser ..........24 Change User Codes Browser .......... 24 Entering User Names ............. 25 Appendix C .............. 26 Common Keypad Displays ..........26 XR100FC/XR500FC User’s Guide...
The best way to survive a fire or other emergency is to get out early. The installation of a fire alarm system, with smoke and carbon monoxide detectors in each room, can greatly decrease your risk of loss or injury. XR100FC/XR500FC User’s Guide...
Page 6
This page intentionally left blank XR100FC/XR500FC User’s Guide...
Fire Command Center The XR100FC/XR500FC comes with a built-in LCD display with a 20-key membrane keyboard called the Fire Command Center. The keyboard is mounted behind an opening in the red enclosure door.
This LED is OFF when no alarm currently displays in the status list. There are four keys under the display called the Select keys. They allow you to choose what to do by pressing the Select key under choices being shown in the display. XR100FC/XR500FC User’s Guide Introduction...
8 display. Press the COMMAND key to display areas 9 through 16. Press the COMMAND key again to display areas 17 through 25. Press the COMMAND key one more time to display areas 26 through 32. Note: Only areas pre-programmed at installation can display. Introduction XR100FC/XR500FC User’s Guide...
At SET VOLUME LEVEL, use the left Select key to lower the keypad volume. Use the right Select key to raise the volume. Model number The keypad model number, firmware version, and date display, but cannot be changed. XR100FC/XR500FC User’s Guide Introduction...
A user has attempted a door access to an armed area to which they do not have arming and disarming authority. TRoUBLE There is a problem with a protection device or system component. This display is accompanied by a description of the problem. Introduction XR100FC/XR500FC User’s Guide...
Press a Select key to silence. What to do when the trouble tone sounds You can silence the trouble tone by pressing any key. This only silences the keypad and does not correct the condition that originally caused the trouble. XR100FC/XR500FC User’s Guide Introduction...
Some features displayed on the User Menu are not necessary for the model and version numbers. XR100FC/XR500FC Addressable Fire Alarm Control Panel. Please SYSTEM TEST Tests the system siren, communication disregard these prompts and displays. Press the COMMAND key to to the central station, and backup skip any displays and prompts not discussed in this User Guide.
3. The keypad displays SENSORS OFF for five seconds followed 2. The keypad displays ALARM SILENCE?. by SENSORS ON. 3. Press any Select key to silence the bells and exit the User 4. The keypad automatically exits the User Menu. Menu. XR100FC/XR500FC User’s Guide System Setup...
8. Press the Back Arrow key to exit the User Menu. Browser Feature unsure output number, refer Appendix B at the back of this guide for a diagram showing you how to use the built-in Outputs ON/OFF browser. System Setup XR100FC/XR500FC User’s Guide...
3b. Select BYPS for a list of zones that are currently bypassed. 3c. Select ALR for a list of zones that have gone into alarm during the current or previous armed period. 3d. Press NBR and ZONE NO: - displays. XR100FC/XR500FC User’s Guide System Setup...
TEST END to indicate the System Test is complete. VER_201_3/08/04), the panel model (MODEL XR500N), and You can press the Back Arrow key to end the transmit then exits the User Menu. test. * The transmit test does not occur on local systems. System Setup XR100FC/XR500FC User’s Guide...
Note: During the Panic Zone Test, any zones that fail are not sent to the receiver unless pre-programmed at installation to be sent. Always make sure that at least one administrator in your system has a profile with all authorities and all areas. XR100FC/XR500FC User’s Guide System Setup...
TEMP EXPIRE DATE:. Enter the ending date for the profile to RE ARM DLY 0 – 250 Re-Arm Delay expire. Default is seven days from today. The system deletes Temp users at 12:00 AM on the last date. SEC LANGUAGE Preferred Language System Setup XR100FC/XR500FC User’s Guide...
Browser Feature Refer to Appendix B in this guide for a diagram showing you how to use the Output Group browser and the Profile browsers. XR100FC/XR500FC User’s Guide System Setup...
Page 21
6 and 7 repeat. The User Profile assignment is automatically selected for the next user based on the previous user entered. This batch entry method speeds up user entry in large systems. System Setup XR100FC/XR500FC User’s Guide...
Refer to Appendix B for diagrams showing you how to use the User Press COMMAND. Codes Add, Delete, and Change browsers. The display returns to the TIME DAY DATE display. Press the Back Arrow key to exit the User Menu. XR100FC/XR500FC User’s Guide System Setup...
2. The Fire Drill test automatically ends with ALARM SILENCE or system memory. Also, once the full 12,000 events are stored, any the programmed Bell Cutoff time. new event causes the oldest event to be cleared. See Appendix A for Display Events. System Setup XR100FC/XR500FC User’s Guide...
Display Events or press SRT to define a new sort. 4. To use the Sort feature, press the Select key under SRT. The keypad displays FRST DATE: 8/21. Press any Select key and enter a 4-digit beginning date for the sort. Press COMMAND. XR100FC/XR500FC User’s Guide Appendix A...
ALR - Alarm TBL - Trouble RST - Restore FLT - Zone Fault SVC - Service smoke detector LOW - Low battery MIS - Missing wireless transmitter Note: LOW and MIS are for wireless systems only. Appendix A XR100FC/XR500FC User’s Guide...
System Monitor Event Names - There are 5 system monitors: POWER - AC power to panel BATTERY - On panel LINE 1 - Phone line number 1 LINE 2 - Phone line number 2 TAMPER - On panel box XR100FC/XR500FC User’s Guide Appendix A...
COMMAN -BAD O = the zone is open -BAD O = the zone is open another zone number. -BAD S = the zone is shorted -BAD S = the zone is shorted Appendix B XR100FC/XR500FC User’s Guide...
The next output group name SELECT ZONE . . . displays. OUTPUT: 127 ON OFF The display shows the door or DOOR: 128 ON OFF output number. Press any Select key and the output group number FRONT OFFICE displays. XR100FC/XR500FC User’s Guide Appendix B...
The default user name appears. USER 012 Press any SELECT key to clear When you complete changes this name. PROFILE 12 CHNGD to the profile, press COMMAND. See the Entering User Names diagram at the end of this Appendix Appendix B XR100FC/XR500FC User’s Guide...
Follow the prompts to complete the code change. You can also press any SELECT key KATIE SMITH here to clear a custom user name and use the USER 13 DELETED data entry keys to enter a new user name. XR100FC/XR500FC User’s Guide Appendix B...
Pressing the 9 key provides you Pressing the 0 (zero) key provides with Y, Z, and a space to use you with a – (dash), . (period), between names. For example: * (asterisk), and a # (pound sign). BOB SMITH. Appendix B XR100FC/XR500FC User’s Guide...
Appendix C Common Keypad Displays Listed below are several keypad messages you may see on the display. Follow the instructions in the Possible Solutions column to correct the problem. In many cases, you need to call a service person to correct the problem. Displays that are not discussed here mean that your service representative should be called.
Page 33
Output Groups 22 Exit 6 Silenced 5 Zone Status 21 Fire Alarm 6 Supervisory 5 Key Press 6 System Busy 6 Prewarn 6 Change User Codes 16 System Trouble 6 Trouble 6 Browser 24 Trouble 5 Index XR100FC/XR500FC User’s Guide...
Page 34
Status LEDs 2 Zone Status 10 Trouble LED 2 System Busy 6 Browser 21 System Status 11 System Test 11 Multi-lingual Display 3 System Trouble 6 Outputs On/Off 9 TEMP CODE 13 Browser 22 Tones 6 Output Groups XR100FC/XR500FC User’s Guide Index...