Download
Share
Print this page
  1. Manuals
  2. Brands
  3. N-BIOTEK Manuals
  4. Laboratory Equipment
  5. NB504CIR
  6. Operation manual

N-BIOTEK NB504CIR Operation Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
NB504CIR Operation Manual
Model : NB504CIR
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the NB504CIR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for N-BIOTEK NB504CIR

Summary of Contents for N-BIOTEK NB504CIR

  • Page 1 NB504CIR Operation Manual Model : NB504CIR...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS CONTENTS PAGE SAFETY AND GENERAL PRECAUTION TRANSPORTATION, STORAGE, AND LOCATION OF INSTALLATION PREREQUISIT AND CONFIGURATION FEATURES AND SPECIFICATIONS CONTROL PANEL OPERATION SAFETY SWITCH & MAINTENANCE TROUBLESHOOTING...

  • Page 3: Safety And General Precaution

    1. SAFETY AND GENERAL PRECAUTION 1. 1 General Information on Precaution This equipment must be operated as described in this manual. if operational guideline is not followed, equipment damage and personal injury can occur. Please follow this mark to prevent equipment damage of personal injury. If you don't keep this caution, you can get injured as well as a property loss.
  • Page 4 1.3 Precaution for ground connection Please ground before use the product, if you don't ground, you could get an electric shock when malfunction or an electric leakage occurs. At the place where you can't ground, * Please buy the equipment to prevent any electrical leakage. * An electric shock, an electric leakage and a fire can be occurred without an electric leakage breaker.

  • Page 5: Transportation, Storage, And Location Of Installation

    When you don't use the product or clean it, please pull out the power plug. (It is to prevent an eclectic leakage.) Open and close the door softly and please use a door knob. (A heavy shock can damage the product and breakdown the operating part. Also, your hands can be stuck between the door and body.) Do not detach the built-in lamp and electrical devices.
  • Page 6 2.3 Location of installation and ambient conditions Do not put flammable substances near the product. (It may cause a fire.) When you install the product, you are required to keep the distance at least 30cm from the wall. To completely separate the unit from the power supply, power plug must be disconnected.

  • Page 7: Prerequisit And Configuration

    When you have received the instrument which is packed on pallet, inspect the box carefully for any damages that may have caused any damages to product during shipping. Please report any damage to the carrier or to your local N-BIOTEK distributor immediately. Location The incubator is designed to operate at temperature 4℃.
  • Page 8 3.2 Configuration <Figure #1> 1. Safety Lid 6. Chamber, Rotor 2. Vacuum Gauge 7. Front Cover 3. Control Panel 8. Main Power 4. Cold Trap 9. Safety Switch 5. IR Lid <Figure #2> Note: There is a vertical empty gap on rotor. That gap must face to chamber, not to rotor inside in order to create centrifugal force.
  • Page 9 <Figure #4> At the rear of NB504CIR, there is a port where air in chamber comes out as vacuum fills up in chamber. There might be a sound of air coming through this port until chamber gets to vacuum condition.

  • Page 10: Features And Specifications

    → Induction motor barely makes noise and vibration. Plus, this gives less maintenance required. 5. User-friendly operation designed 6. Compact & mobile system → It is suited for individual researchers with limited footprint. 4.2 Specification Items NB504CIR Temperature Range +4℃ to 80℃ Increment 0.1℃...

  • Page 11: Control Panel

    5. CONTROL PANEL Pilot Lamp of Overheating When overheating is detected by the safety device, GREEN light will be on Pilot Lamp of Heating Shows which mode of Heating is on by displaying different colors - IR: GREEN light - IR/HEAT: ORANGE light - HEAT: RED light HEAT Mode Selector Use to select IR, IR/HEAT, or HEAT mode...

  • Page 12: Operation

    6. OPERATION The location where you are desired to use it should be flat, balanced surface to keep the unit stable. Before connecting the power cable to the plug, make sure that the unit is turned off to avoid any electric shock.
  • Page 13 [Time Setting] 1) At the same time as set temperature saved, it will move on to Time Setting. On LED display, ‘HOUR’ section will flicker. 2) Adjust to set ‘HOUR’ section by using INCREASE & DECREASE button. 3) Press SET button again and it will move on to ‘MINUTE’ section. Adjust to set ‘MINUTE’...

  • Page 14: Safety Switch & Maintenance

    [Note] When restart the operation or turn on the power after 2), 3), or 4) : The set value will be reset to the previous set value. Cold trap power can be turned on only when the main power is on. Cold trap power is turned on/off only through the Cold Trap Power S/W.

  • Page 15: Troubleshooting

    Leaks in lines or Locate and repair connectors or gasket Foreign material on lid gasket Clean gasket and lid Manufactured by : N-BIOTEK, Inc. 402-803 Techno park, 655 Pyeongcheon-ro, Yakdae-dong, Wonmi-gu, Bucheon-si, Gyeongi Province, Korea Tel : +82-32-321-2100 | E-mail : export@n-biotek.com...