Advertisement
Advertisement
Related Manuals for N-BIOTEK NB-205
Summary of Contents for N-BIOTEK NB-205
- Page 1 OPERATING MANUAL SHAKING INCUBATOR MODEL : NB-205...
-
Page 2: Table Of Contents
N-BIOTEK www.n-biotek.com Table of Contents CONTENTS PAGE SAFETY INSTRUCTION TRANSPORTATION, STORAGE, AND LOCATION OF INSTALLATION FEATURE, SPECIFICATION, CONTROL PANEL INSTALLATION AND OPERATION SERVICE AND CHECK POINT WARRANTY NB-205(Ver. 2020) 2/13... - Page 3 (When it is damaged, it can cause a fire.) Do not touch the power cord with wet hands. (It can cause an electric shock.) Do not use the damaged power cord and outlet. (It can cause an electric shock and a fire.) NB-205(Ver. 2020) 3/13...
- Page 4 (It can cause a fire and an explosion.) To prevent water and experiment material from going into the control panel during the experiment, make sure to clean the control panel with a dry cloth. (It can cause an electric leakage and a fire.) NB-205(Ver. 2020) 4/13...
-
Page 5: Transportation, Storage, And Location Of Installation
(It causes an electric leakage accident and a corrosive of the product.) Keep this product out of the direct ray of sun and do not install at a hot place or a place that is near an electric heat. (The proper indoor temperature is 20℃ ~ 30℃.) NB-205(Ver. 2020) 5/13... - Page 6 (When the product is moved, the movable door can cause injury of you and damage of the product.) When you move the product, you must hold up the product. (Pushing or pulling the product can damage the bottom part of the product.) NB-205(Ver. 2020) 6/13...
-
Page 7: Feature, Specification, Control Panel
Blushless DC motor and beltless drive system for shaker minimizes noise and vibration. ● Easy - Platform Installation Very simple way to place holder or spring rack platform on the shaker. And Optional accessories available for most common laboratory vessels 3. 2 Specification NB-205(Ver. 2020) 7/13... - Page 8 4. SETTING Button for Temperature 5. Adjustment Button(up and down) for Temperature 6. RPM / TIME Switch Button 7. SETTING Button for RPM / TIME 8. Adjustment Button(up and down) for RPM / TIME 9. START/STOP Button NB-205(Ver. 2020) 8/13...
-
Page 9: Installation And Operation
LED screen will be stop to flicker and saved as new temperature. * if you don’t press “SET” key after set up the new temperature, new set-up temperature will not save at all. * Set-up temperature range is Ambient +5℃ to 60℃ NB-205(Ver. 2020) 9/13... - Page 10 (1) In the beginning, press the “RPM/TIME” key for 1 or 2 seconds until LED blinks then put desired RPM value by using UP(▲), DOWN(▼) key and press “SET” button to save RPM. * RPM setting range is from 30 to 300. NB-205(Ver. 2020) 10/13...
- Page 11 (This message may occur from 200 RPM) - Solution : These symptom will be recovered automatically within 3 min or restart it. 3) This message may be displayed as to - Finish operation after "TIME" Setting Mode. NB-205(Ver. 2020) 11/13...
-
Page 12: Service And Check Point
1) Unit is not working (Check below before thinking this as malfunction) (1) Electrical connection Please disconnect main power cable and then reconnect. (2) Voltage supply Please check to voltage. (3) Fuse check. (4) Verify voltage on unit. (5) Defective power switch (check voltage at switch) NB-205(Ver. 2020) 12/13... -
Page 13: Warranty
N-BIOTEK, whichever is sooner as indicated in above table. This period is proved by serial no. 3. N-BIOTEK will not be responsible of free warranty service for the faulty caused by user’s improper operation, excessive use, use of incorrect voltage & frequency, storage in wrong environment mentioned in Manual.