ICE AIR RSNU Installation Manual

ICE AIR RSNU Installation Manual

Packaged terminal air conditioner (ptac) unit for new construction

Advertisement

Quick Links

RSNU
Installation Manual
Durable
Ultra-High
Efficiency AC
Packaged Terminal Air Conditioner
(PTAC) Unit for New Construction

Advertisement

Table of Contents
loading

Summary of Contents for ICE AIR RSNU

  • Page 1 RSNU Installation Manual Durable Ultra-High Efficiency AC Packaged Terminal Air Conditioner (PTAC) Unit for New Construction...
  • Page 2: Table Of Contents

    National Electric Code. The proper installation of this unit is described in the following sections. Following the steps in the order presented should ensure proper installation. Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 3: Overview/Application Note/Inspection

    NOTE: It is the responsibility of the purchaser to file all necessary claims with the delivering carrier in a timely fashion. Many carriers have a 15 day notice period from receipt of delivery to file any and all claims. Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 4: General Specifications

    The performance data shown above is based on standard equipment under the provided design conditions. Performance may vary depending on equipment configuration and project site conditions. Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 5: Before You Begin

    SLEEVE LEVELS INSTALL ABOVE FINISHED FLOOR AS DETERMINED BY JOB CONDITIONS REFER TO CERTIFIED DRAWINGS Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 6 1.000 " 16.000 " 1.125 " 16.380 " 12.000 " 4.000 " FRONT VIEW PITCH 1/4" TOWARD REAR REAR VIEW SECTION A-A Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 7: Installation

    7. Caulk wall sleeve (from inside the 5. After mortar has dried, remove the Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 8: Panel/Window Construction Sleeve Installation

    All louvers by other manufacturers must be approved by qualified installer prior to installation. Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 9: Installing The Louver (Optional)

    WASHERS & NUTS OPTIONAL SUPPORT ( 4 EACH ) ANGLE Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice. NOTE: THREADED STUDS MUST BE SLIDABLE ABOUT 2" UP AND DOWN...
  • Page 10: Installing The Hydronic Heating Assembly (Optional)

    8.723" 7.298" 42.625" FRONT VIEW RIGHT VIEW SLEEVE SUPPLY END RETURN END HEADER HEADER ( STEAM ONLY ) HTG. COIL ASSEMBLY Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 11: Installing The Chassis

    T.O.S. KICK PLATE FRONT VEW WALL SLEEVE COOLING CHASSIS SHEETROCK SLOT TO ATTACH CHASSIS CLIP CHASSIS CLIP Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 12: Installing The Enclosure And Enclosure

    TOP VIEW 2.297" 1.438" .500" 22.000" 14.500" 3.000" 7.500" FRONT VIEW SECTION A-A SLEEVE ENCLOSURE WASHER & NUT MOUNTING ADJ. LEGS STUDS Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 13: Installing The Lateral Duct Kit (Optional)

    Drilled hole is not required for wall mounted thermostat. 12.500" (SLEEVE 20.000" DEPTH) 4.500" 2.625" FRONT VIEW SECTION A-A Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 14: General Wiring Diagram

    General Wiring Diagram Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 15: Product Nomenclature

    Wall Mounted with 50 ft Wire Whip MERV 13 Filter UNIT TYPE Standard 18" wire whip Washable Filter Unit Mounted Controls Fiberglass Filter No Filter Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.
  • Page 16: Warranty/Contact Information

    © 2023 by Ice Air, LLC ICE6149.1 11/23 Due to Ice Air’s ongoing product development programs, the information in this document is subject to change without notice.

Table of Contents